3D Printed Microneedles for the Transdermal Delivery of NAD + Precursor: Toward Personalization of Skin Delivery
ACS Biomaterials Science & Engineering · 2024
DOI: 10.1021/acsbiomaterials.4c00905 ↗Kurz gefasst
Fachartikel in der Zeitschrift ACS Biomaterials Science & Engineering, 2024. Verfasst von Masood Ali und 7 weiteren Autor:innen. Beteiligte Einrichtung: Frazer Institute, Faculty of Medicine, The University of Queensland, Brisbane, QLD 4102, Australia. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Needles, Administration, Cutaneous. Die Arbeit wurde bisher 16-mal zitiert (Crossref) und nennt 119 Literaturangaben.
Abstract (Originalsprache)
3D printing of microneedles (μNDs) for transdermal therapy has the potential to enable patient personalization based on the target disease, site of application, and dosage requirements. To convert this concept to reality, it is necessary that the 3D printing technology can deliver high resolution, an affordable cost, and large print volumes. With the introduction of benchtop 4K and 8K 3D printers, it is now possible to manufacture medical devices like μNDs at sufficient resolution and low cost. In this research, we systematically optimized the 3D printing design parameters such as resin viscosity, print angle, layer height, and curing time to generate customizable μNDs. We have also developed an innovative 3D coating microtank device to optimize the coating method. We have applied this to the development of novel μNDs to deliver an established NAD+ precursor molecule, nicotinamide mononucleotide (NMN). A methacrylate-based polymer photoresin (eSun resin) was diluted with methanol to adjust the resin viscosity. The 3D print layer height of 25 μm yielded a smooth surface, thus reducing edge-ridge mismatches. Printing μNDs at 90° to the print platform yielded 84.28 ± 2.158% (n = 5) of the input height thus increasing the tip sharpness (48.52 ± 10.43 μm, n = 5). The formulation containing fluorescein (model molecule), sucrose (viscosity modifier), and Tween-20 (surface tension modifier) was coated on the μNDs using the custom designed microtank setup, and the amount deposited was determined fluorescently. The dye-coated μND arrays inserted into human skin (in vitro) showed a fluorescence signal at a depth of 150 μm (n = 3) into the skin. After optimization of the 3D printing parameters and coating protocol using fluorescein, NMN was coated onto the μNDs, and its diffusion was assessed in full-thickness human skin in vitro using a Franz diffusion setup. Approximately 189 ± 34.5 μg (5× dipped coated μNDs) of NMN permeated through the skin and 41.2 ± 7.53 μg was left in the skin after 24 h. Multiphoton microscopy imaging of NMN-coated μND treated mouse ear skin ex vivo demonstrated significantly (p < 0.05) increased free-unbound NADPH and reduced fluorescence lifetime of NADPH, both of which are indicative of cellular metabolic rates. Our study demonstrates that low-cost benchtop 3D printers can be used to print high-fidelity μNDs with the ability to rapidly coat and release NMN which consequently caused changes in intracellular NAD+ levels.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Frazer Institute, Faculty of Medicine, The University of Queensland, Brisbane, QLD 4102, Australia.
- School of Agriculture and Food Sciences, The University of Queensland, Brisbane, QLD 4072, Australia.
- Centre for Biomedical Technologies, School of Mechanical, Medical and Process Engineering, Queensland University of Technology, Brisbane, QLD 4059, Australia.
- Curtin Medical School, Curtin University, Bentley, WA 6102, Australia.
- School of Materials Science and Engineering, The University of New South Wales, Sydney, NSW 2052, Australia.
- Australian Centre for Nanomedicine, The University of New South Wales, Sydney, NSW 2052, Australia.
ORCID-Profile: Masood Ali, Tushar Kumeria, Yousuf Mohammed
Zitieren
APA
Ali, M., Namjoshi, S., Phan, K., Wu, X., Prasadam, I., Benson, H. A. E., Kumeria, T., & Mohammed, Y. (2024). 3D Printed Microneedles for the Transdermal Delivery of NAD + Precursor: Toward Personalization of Skin Delivery. ACS Biomaterials Science & Engineering. https://doi.org/10.1021/acsbiomaterials.4c00905
Vancouver
Ali M, Namjoshi S, Phan K, Wu X, Prasadam I, Benson HAE, et al. 3D Printed Microneedles for the Transdermal Delivery of NAD + Precursor: Toward Personalization of Skin Delivery. ACS Biomaterials Science & Engineering. 2024. doi:10.1021/acsbiomaterials.4c00905
BibTeX
@article{Ali2024,
author = {Ali, Masood and Namjoshi, Sarika and Phan, Khanh and Wu, Xiaoxin and Prasadam, Indira and Benson, Heather A E and Kumeria, Tushar and Mohammed, Yousuf},
title = {3D Printed Microneedles for the Transdermal Delivery of NAD + Precursor: Toward Personalization of Skin Delivery},
journal = {ACS Biomaterials Science & Engineering},
year = {2024},
doi = {10.1021/acsbiomaterials.4c00905}
}
EUVIMED