EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Comparative PECS and LPBF Processing of Bi0.5Sb1.5Te3: Microstructure, Texture, and Thermoelectric Performance

Mateusz Pindel iD, Taras Parashchuk iD, Piotr Ledwig, Hubert Pasiowiec, Mykola Maksymuk, Grzegorz Cios, Beata Dubiel, Krzysztof T Wojciechowski iD

ACS Applied Materials & Interfaces · 11.11.2026 · 18 (44) · 60680-60693

DOI: 10.1021/acsami.6c14017 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Applied Materials & Interfaces, online erschienen am 03.11.2026. Verfasst von Mateusz Pindel und 7 weiteren Autor:innen. Beteiligte Einrichtung: Thermoelectric Research Laboratory, Department of Inorganic Chemistry, Faculty of Materials Science and Ceramics, AGH University of Krakow, Mickiewic…. Die Arbeit nennt 68 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Fundacja na rzecz Nauki Polskiej, Narodowe Centrum Nauki.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Laser powder bed fusion (LPBF) is emerging as a promising manufacturing route for next-generation thermoelectric generators, offering unprecedented freedom in the fabrication of complex device geometries. However, the rapid melting and solidification inherent to LPBF produce microstructures fundamentally different from those of conventional consolidation techniques, and how these processing-induced features affect thermoelectric performance remains poorly understood. In this work, LPBF-produced p-type Bi0.5Sb1.5Te3 was compared with materials fabricated by pulsed electric current sintering (PECS), which served as a reference processing route providing a higher degree of crystallographic texture. The comparison enabled identification of the microstructural characteristics governing electrical and thermal transport. In particular, the investigated materials exhibited a wide range of preferred orientation (Lotgering factor F ≈ 0.02–0.20), while maintaining comparable Seebeck coefficients (∼160–175 μV K–1). In contrast, electrical conductivity (720–2200 S cm–1 at 300 K), thermal conductivity (0.9–1.5 W m–1 K–1), and consequently the thermoelectric figure of merit varied strongly with the processing route and crystallographic orientation. PECS samples with moderate preferred orientation reached ZT ≈ 1.1, while LPBF specimens exhibited ZT ≈ 0.4–0.5. The lower LPBF performance reflects weaker texture and processing-induced defects, partly related to nonideal powder morphology and feeding conditions. Additionally, numerical modeling (FEM) was performed to evaluate energy conversion efficiency, demonstrating higher output power and overall efficiency for the PECS samples compared to the LPBF ones. The comparative analysis demonstrates that crystallographic texture and microstructural integrity are key factors affecting thermoelectric performance and identifies processing-related limitations under the LPBF conditions investigated in this study.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturingbismuth tellurideenergy conversion efficiencypreferred orientationthermoelectric properties

Autor:innen und Institutionen

  • Thermoelectric Research Laboratory, Department of Inorganic Chemistry, Faculty of Materials Science and Ceramics, AGH University of Krakow, Mickiewicza Ave. 30, 30-059Krakow, Poland.
  • Department of Metal Forming and Metallurgical Engineering, Faculty of Metals Engineering and Industrial Computer Science, AGH University of Krakow, Mickiewicza Ave. 30, 30-059Krakow, Poland.
  • Academic Centre for Materials and Nanotechnology, AGH University of Krakow, Mickiewicza Ave. 30, 30-059Krakow, Poland.

ORCID-Profile: Mateusz Pindel, Taras Parashchuk, Krzysztof T Wojciechowski

Förderung

  • Fundacja na rzecz Nauki Polskiej
  • Narodowe Centrum Nauki

Zitieren

APA

Pindel, M., Parashchuk, T., Ledwig, P., Pasiowiec, H., Maksymuk, M., Cios, G., Dubiel, B., & Wojciechowski, K. T. (2026). Comparative PECS and LPBF Processing of Bi0.5Sb1.5Te3: Microstructure, Texture, and Thermoelectric Performance. ACS Applied Materials & Interfaces, 18(44), 60680-60693. https://doi.org/10.1021/acsami.6c14017

Vancouver

Pindel M, Parashchuk T, Ledwig P, Pasiowiec H, Maksymuk M, Cios G, et al. Comparative PECS and LPBF Processing of Bi0.5Sb1.5Te3: Microstructure, Texture, and Thermoelectric Performance. ACS Applied Materials & Interfaces. 2026;18(44):60680-60693. doi:10.1021/acsami.6c14017

BibTeX
@article{Pindel2026,
  author = {Pindel, Mateusz and Parashchuk, Taras and Ledwig, Piotr and Pasiowiec, Hubert and Maksymuk, Mykola and Cios, Grzegorz and Dubiel, Beata and Wojciechowski, Krzysztof T},
  title = {Comparative PECS and LPBF Processing of Bi0.5Sb1.5Te3: Microstructure, Texture, and Thermoelectric Performance},
  journal = {ACS Applied Materials & Interfaces},
  year = {2026},
  volume = {18},
  number = {44},
  pages = {60680--60693},
  doi = {10.1021/acsami.6c14017}
}
Kostenlos starten →