EUVIMEDEUVIMED entdecken
Crossref

In Situ Hole-Transport Layer Formation and Concurrent Passivation for FA0.9Cs0.1PbI3 Perovskite Solar Cells

Rashid Khan iD, Yiming Du, Junyao Gao, Meihui Song, Hua Wang iD, Lin Chen, Zhengguo Xiao iD, Xingyou Tian

ACS Applied Materials & Interfaces · 05.08.2026 · 18 (30) · 41041-41051

DOI: 10.1021/acsami.6c09672 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Applied Materials & Interfaces, online erschienen am 25.07.2026. Verfasst von Rashid Khan und 7 weiteren Autor:innen. Beteiligte Einrichtung: Institute of Solid State Physics, Hefei Institutes of Physical Science, Chinese Academy of Sciences, Hefei230031, China. Die Arbeit nennt 54 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The buried interface between the hole transport layer (HTL) and the perovskite layer is critical to both the efficiency and stability of inverted perovskite solar cells (PSCs). The conventional sequential deposition approach, where the self-assembled monolayer (SAM)-based HTL is pre-deposited as a separate bottom layer prior to perovskite coating, faces inherent challenges, including insufficient interfacial wetting, high defect densities, and limited scalability. Herein, we introduce a dynamic self-assembly (DSA) approach to simultaneously fabricate the HTL and passivate the perovskite in a single step. By integrating a binary mixture of SAMs ([2-(3,6-dimethoxy-9H-carbazol-9-yl)ethyl]phosphonic acid (MeO-2PACz) and [4-(3,6-dimethyl-9H-carbazol-9-yl)butyl]phosphonic acid (Me-4PACz)) and the monomer 2-(dimethylamino)ethyl methacrylate (DMAEMA) directly into the perovskite precursor, an in situ, uniform HTL forms during perovskite crystallization. The SAMs optimize energy alignment and interfacial contact, while the polymerized DMAEMA, localized at grain boundaries, passivates undercoordinated Pb2+ and suppresses iodide-related defects. This combined approach enhances film crystallinity, improves interfacial homogeneity, and drastically reduces non-radiative recombination. Consequently, the champion device achieves a power conversion efficiency (PCE) of 22.03% with a high open-circuit voltage (Voc) of 1.11 V, a short-circuit current density of 25.84 mA cm–2, and a fill factor of 77%. Moreover, the DSA-processed device remains operational throughout prolonged maximum power point (MPP) tracking under continuous illumination and elevated temperature. This work presents DSA as an effective strategy for simultaneous buried interface engineering and defect passivation in inverted PSCs.

Schlagwörter

Stichwörter der Autor:innen

defects passivationinterface engineeringmixed self-assembled monolayermonomer self-polymerizationperovskite solar cells

Autor:innen und Institutionen

  • Institute of Solid State Physics, Hefei Institutes of Physical Science, Chinese Academy of Sciences, Hefei230031, China.
  • University of Science and Technology of China , Hefei230026, China.
  • Hefei National Research Center for Physical Science at the Microscale, Department of Physics, CAS Key Laboratory of Strongly-Coupled Quantum Matter Physics, University of Science and Technology of China, Hefei, Anhui230…

ORCID-Profile: Rashid Khan, Hua Wang, Zhengguo Xiao

Zitieren

APA

Khan, R., Du, Y., Gao, J., Song, M., Wang, H., Chen, L., Xiao, Z., & Tian, X. (2026). In Situ Hole-Transport Layer Formation and Concurrent Passivation for FA0.9Cs0.1PbI3 Perovskite Solar Cells. ACS Applied Materials & Interfaces, 18(30), 41041-41051. https://doi.org/10.1021/acsami.6c09672

Vancouver

Khan R, Du Y, Gao J, Song M, Wang H, Chen L, et al. In Situ Hole-Transport Layer Formation and Concurrent Passivation for FA0.9Cs0.1PbI3 Perovskite Solar Cells. ACS Applied Materials & Interfaces. 2026;18(30):41041-41051. doi:10.1021/acsami.6c09672

BibTeX
@article{Khan2026,
  author = {Khan, Rashid and Du, Yiming and Gao, Junyao and Song, Meihui and Wang, Hua and Chen, Lin and Xiao, Zhengguo and Tian, Xingyou},
  title = {In Situ Hole-Transport Layer Formation and Concurrent Passivation for FA0.9Cs0.1PbI3 Perovskite Solar Cells},
  journal = {ACS Applied Materials & Interfaces},
  year = {2026},
  volume = {18},
  number = {30},
  pages = {41041--41051},
  doi = {10.1021/acsami.6c09672}
}
Kostenlos starten →