EUVIMEDOpdag EUVIMED
Crossref

Tuning Microstructural, Optical, and Electrical Properties of CsSnI 3 via Sequential Thermal Evaporation for Photovoltaic Application

Corinna Ponti iD, Enrica Luzzi iD, Elena Santoro, Manuela Ferrara, Carmen Serpico, Debendra Prasad Panda, Paolo Aprea iD, Antonio Abate iD, Paola Delli Veneri, Lucia V Mercaldo iD

ACS Applied Materials & Interfaces · 2026-03-25 · 18 (11) · 16384-16395

DOI: 10.1021/acsami.5c23764 ↗

At a glance

Journal article in ACS Applied Materials & Interfaces, published online on 2026-03-13. Written by Corinna Ponti and 9 co-authors. Institution: Department of Chemical, Materials and Industrial Production Engineering, University of Naples Federico II, Naples 80125, Italy. Cited 3 times so far (Crossref); 38 references. Funded by: Ministero dell'ambiente e della sicurezza energetica.

AbstractSubjectsBibliografiske oplysningerCiteRelated studies

Abstract (original language)

Tin halide formulations are emerging as the leading sustainable, lead-free options for thin-film perovskite solar cells. In this study, we focused on the fully inorganic CsSnI3 composition and systematically explored a solvent-free approach to manufacturing device-grade films via sequential thermal evaporation under vacuum. This production technique is compatible with industry standards, offers fewer constraints than coevaporation, and holds great promise for Pb-based perovskite fabrication but has yet to be thoroughly investigated for tin-based formulations. By eliminating solvents, the approach could also prove effective in mitigating the inherent self-p-doping of these materials, a critical requirement for achieving high-efficiency devices. We tested both double- and multilayer fabrication protocols and compared the structural, morphological, optical, and electrical properties of as-deposited and annealed films. This investigation was complemented by integrating the evaporated CsSnI3 layers into p-i-n solar cells as a diagnostic tool. Our findings provide insights into (i) the impact of the deposition protocol on the material properties and (ii) the potential for fine-tuning them via postdeposition thermal treatments. Both methods yielded highly crystalline and compact films, while self-p-doping persisted in pure stoichiometric CsSnI3 films, with a free hole density of around 1019 cm-3 regardless of the protocol. Notably, a 1-order-of-magnitude reduction in the hole density was achieved by incorporating SnF2 as a reducing agent. Readily implemented via the deposition of an additional layer, the inclusion of additives emerges as a necessary yet viable route toward device-grade evaporated CsSnI3.

Subjects

Author keywords

full inorganiclead-freeperovskitephotovoltaicsthin filmtinvapor deposition

Authors and institutions

  • Department of Chemical, Materials and Industrial Production Engineering, University of Naples Federico II, Naples 80125, Italy.
  • Italian National Agency for New Technologies, Energy and Sustainable Economic Development (ENEA), Portici Research Center, Portici (Naples) 80055, Italy.
  • Department of Chemical Sciences, University of Naples Federico II, Naples 80126, Italy.

ORCID profiles: Corinna Ponti, Enrica Luzzi, Paolo Aprea, Antonio Abate, Lucia V Mercaldo

Funding

  • Ministero dell'ambiente e della sicurezza energetica

Cite

APA

Ponti, C., Luzzi, E., Santoro, E., Ferrara, M., Serpico, C., Panda, D. P., Aprea, P., Abate, A., Delli Veneri, P., & Mercaldo, L. V. (2026). Tuning Microstructural, Optical, and Electrical Properties of CsSnI 3 via Sequential Thermal Evaporation for Photovoltaic Application. ACS Applied Materials & Interfaces, 18(11), 16384-16395. https://doi.org/10.1021/acsami.5c23764

Vancouver

Ponti C, Luzzi E, Santoro E, Ferrara M, Serpico C, Panda DP, et al. Tuning Microstructural, Optical, and Electrical Properties of CsSnI 3 via Sequential Thermal Evaporation for Photovoltaic Application. ACS Applied Materials & Interfaces. 2026;18(11):16384-16395. doi:10.1021/acsami.5c23764

BibTeX
@article{Ponti2026,
  author = {Ponti, Corinna and Luzzi, Enrica and Santoro, Elena and Ferrara, Manuela and Serpico, Carmen and Panda, Debendra Prasad and Aprea, Paolo and Abate, Antonio and Delli Veneri, Paola and Mercaldo, Lucia V},
  title = {Tuning Microstructural, Optical, and Electrical Properties of CsSnI 3 via Sequential Thermal Evaporation for Photovoltaic Application},
  journal = {ACS Applied Materials & Interfaces},
  year = {2026},
  volume = {18},
  number = {11},
  pages = {16384--16395},
  doi = {10.1021/acsami.5c23764}
}
Start for free →