EUVIMEDObjevte EUVIMED
Crossref

In Situ Polymerization of a Self-Healing Polyacrylamide-Based Eutectogel as an Electrolyte for Zinc-Ion Batteries

Xinru Li, Zhongxu Li, Zixian Guo, Chen Zhang, Xueer Xu, Jiangping Tu iD, Xiuli Wang iD, Changdong Gu iD

ACS Applied Materials & Interfaces · 2024-07-17 · 16 (28) · 36901-36910

DOI: 10.1021/acsami.4c05293 ↗

At a glance

Journal article in ACS Applied Materials & Interfaces, published online on 2024-07-09. Written by Xinru Li and 7 co-authors. Institution: School of Materials Science and Engineering, State Key Laboratory of Silicon and Advanced Semiconductor Materials, Zhejiang University, Hangzhou 3100…. Cited 38 times so far (Crossref); 41 references. Funded by: Zhejiang University.

AbstraktSubjectsBibliografické údajeCiteRelated studies

Abstract (original language)

Gel electrolytes have attracted extensive attention in flexible batteries. However, the traditional hydrogel electrolyte is not enough to solve the fundamental problems of zinc anodes, such as dendrite growth, side reactions, and freezing failure at temperatures below zero, which seriously restricts the development of zinc-ion batteries. As a flexible energy storage device, the zinc-ion battery inevitably undergoes multiple stretches, bends, folds, or twists in daily use. Here, a self-healing and stretchable eutectogel, designated as deep eutectic solvent-acrylamide eutectic gel (DA-ETG), was developed as a solid-state electrolyte for zinc-ion batteries. This gel was prepared by immobilizing a high-concentration ZnCl2 deep eutectic solvent (DES) into a polyacrylamide matrix through in situ polymerization under ultraviolet light. The eutectogel electrolyte showed exceptional mechanical properties with a maximum fracture strength of 0.6 MPa and a high ionic conductivity of 6.4 × 10-4 S cm-1. The in situ polymerization of the DA-ETG electrolyte in the assembly of a full solid-state zinc-ion battery increased the electrode-electrolyte interface area contact, reduced the ion transport distance between the electrode and electrolyte, minimized the internal resistance, and enhanced the battery's long-term cycling stability. Using the DA-ETG electrolyte, a remarkably high capacity of 580 mAh g-1 at 0.1 A g-1 was achieved by the zinc-ion battery, and a considerable capacity of 234 mAh g-1 was maintained even at 5 A g-1, showing exceptional rate performance. After 2000 cycles at 2 A g-1, the cell with the eutectogel retained a capacity of 85% with a cycling efficiency close to 98%, which demonstrated excellent cycling stability. The self-healing function enabled the prepared soft battery to be reused multiple times, with full contact between the electrode and electrolyte interface, and without device failures.

Subjects

Author keywords

deep eutectic solventeutectogelflexiblein situself-healing

Authors and institutions

  • School of Materials Science and Engineering, State Key Laboratory of Silicon and Advanced Semiconductor Materials, Zhejiang University, Hangzhou 310027, China.
  • Key Laboratory of Advanced Materials and Applications for Batteries of Zhejiang Province, Hangzhou 310027, China.

ORCID profiles: Jiangping Tu, Xiuli Wang, Changdong Gu

Funding

  • Zhejiang University

Cite

APA

Li, X., Li, Z., Guo, Z., Zhang, C., Xu, X., Tu, J., Wang, X., & Gu, C. (2024). In Situ Polymerization of a Self-Healing Polyacrylamide-Based Eutectogel as an Electrolyte for Zinc-Ion Batteries. ACS Applied Materials & Interfaces, 16(28), 36901-36910. https://doi.org/10.1021/acsami.4c05293

Vancouver

Li X, Li Z, Guo Z, Zhang C, Xu X, Tu J, et al. In Situ Polymerization of a Self-Healing Polyacrylamide-Based Eutectogel as an Electrolyte for Zinc-Ion Batteries. ACS Applied Materials & Interfaces. 2024;16(28):36901-36910. doi:10.1021/acsami.4c05293

BibTeX
@article{Li2024,
  author = {Li, Xinru and Li, Zhongxu and Guo, Zixian and Zhang, Chen and Xu, Xueer and Tu, Jiangping and Wang, Xiuli and Gu, Changdong},
  title = {In Situ Polymerization of a Self-Healing Polyacrylamide-Based Eutectogel as an Electrolyte for Zinc-Ion Batteries},
  journal = {ACS Applied Materials & Interfaces},
  year = {2024},
  volume = {16},
  number = {28},
  pages = {36901--36910},
  doi = {10.1021/acsami.4c05293}
}
Start for free →