EUVIMEDOpdag EUVIMED
ÜbersichtsarbeitOpen access · CC BY 4.0

In Situ Printing of Polylactic Acid/Nanoceramic Filaments for the Repair of Bone Defects Using a Portable 3D Device

Guilherme Castro Brito iD, Gustavo Fernandes Sousa, Moises Virgens Santana, André Sales Aguiar Furtado, Millena de Cassia Sousa E Silva, Thiago Ferreira Candido Lima Verde, Renata Barbosa, Tatianny Soares Alves, Luana Marotta Reis Vasconcellos, Leonardo Alvares Sobral Silva, Vicente Galber Freitas Viana, José Figueredo-Silva and 3 more

ACS Applied Materials & Interfaces · 2025

DOI: 10.1021/acsami.4c05232 ↗

At a glance

Übersichtsarbeit in ACS Applied Materials & Interfaces, 2025. Written by Guilherme Castro Brito and 14 co-authors. Institution: LIMAV-Interdisciplinary Laboratory for Advanced Materials, BioMatLab, Materials Science & Engineering Graduate Program, UFPI-Federal University of Pi…. Major MEDLINE topics: Printing, Three-Dimensional, Polyesters, Nanocomposites. Cited 3 times so far (Crossref); 55 references. The full text is freely available (open access, CC BY 4.0). Funded by: Conselho Nacional de Desenvolvimento Cient?fico e Tecnol?gico.

AbstractSubjectsBibliografiske oplysningerCiteRelated studies

Abstract (original language)

In situ 3D printing is attractive for the direct repair of bone defects in underdeveloped countries and in emergency situations. So far, the lack of an interesting method to produce filament using FDA-approved biopolymers and nanoceramics combined with a portable strategy limits the use of in situ 3D printing. Herein, we investigated the osseointegration of new nanocomposite filaments based on polylactic acid (PLA), laponite (Lap), and hydroxyapatite (Hap) printed directly at the site of the bone defect in rats using a portable 3D printer. The filaments were produced using a single-screw extruder (L/D = 26), without the addition of solvents that can promote the toxicity of the materials. In vitro performance was evaluated in the cell differentiation process with mesenchymal stem cells (MSC) by an alkaline phosphatase activity test and visualization of mineralization nodules; a cell viability test and total protein dosage were performed to evaluate cytotoxicity. For the in vivo analysis, the PLA/Lap composite filaments with a diameter of 1.75 mm were printed directly into bone defects of Wistar rats using a commercially available portable 3D printer. Based on the in vitro and in vivo results, the in situ 3D printing technique followed by rapid cooling proved to be promising for bone tissue engineering. The absence of fibrous encapsulation and inflammatory processes became a good indicator of effectiveness in terms of biocompatibility parameters and bone tissue formation, and the use of the portable 3D printer showed a significant advantage in the application of this material by in situ printing.

Subjects

MeSH terms (MEDLINE)

Printing, Three-DimensionalPolyestersNanocompositesAnimalsRatsMesenchymal Stem CellsRats, WistarDurapatiteCell DifferentiationBiocompatible MaterialsBone RegenerationCell SurvivalMaleOsteogenesisCeramics

Author keywords

3D printingHydroxyapatitebone repairemergency caseslaponite

Substances

poly(lactide)PolyestersDurapatiteBiocompatible Materials

Authors and institutions

  • LIMAV-Interdisciplinary Laboratory for Advanced Materials, BioMatLab, Materials Science & Engineering Graduate Program, UFPI-Federal University of Piauí, Teresina 64049-550, Piauí, Brazil.
  • LAPCON─Laboratory of Polymers and Conjugated Materials, Technology Center CT, Materials Science & Engineering Graduate Program, UFPI-Federal University of Piauí, Teresina 64049-550, Piauí, Brazil.
  • Institute of Science and Technology, São Paulo State University (UNESP) 777 Eng. Francisco José Longo Avenue, São José dos Campos 12245-000, São Paulo, Brazil.
  • Postgraduate Program in Materials Engineering, Federal Institute of Education, Science and Technology (IFPI), Campus Teresina Central, Teresina 64001-270, Piauí, Brazil.
  • Biotechnology Research Center, State University of Piauí, Teresina 64003-120, Piauí, Brazil.
  • Department of Physics, UFPI-Federal University of Piauí, Teresina 64049-550, Piauí, Brazil.

ORCID profiles: Guilherme Castro Brito, Anderson Oliveira Lobo

Funding

  • Conselho Nacional de Desenvolvimento Cient?fico e Tecnol?gico

Cite

APA

Brito, G. C., Sousa, G. F., Santana, M. V., Aguiar Furtado, A. S., E Silva, M. C. S., Lima Verde, T. F. C., Barbosa, R., Alves, T. S., Reis Vasconcellos, L. M., Sobral Silva, L. A., Freitas Viana, V. G., Figueredo-Silva, J., Maia Filho, A. L. M., Marciano, F. R., & Lobo, A. O. (2025). In Situ Printing of Polylactic Acid/Nanoceramic Filaments for the Repair of Bone Defects Using a Portable 3D Device. ACS Applied Materials & Interfaces. https://doi.org/10.1021/acsami.4c05232

Vancouver

Brito GC, Sousa GF, Santana MV, Aguiar Furtado AS, E Silva MCS, Lima Verde TFC, et al. In Situ Printing of Polylactic Acid/Nanoceramic Filaments for the Repair of Bone Defects Using a Portable 3D Device. ACS Applied Materials & Interfaces. 2025. doi:10.1021/acsami.4c05232

BibTeX
@article{Brito2025,
  author = {Brito, Guilherme Castro and Sousa, Gustavo Fernandes and Santana, Moises Virgens and Aguiar Furtado, André Sales and E Silva, Millena de Cassia Sousa and Lima Verde, Thiago Ferreira Candido and Barbosa, Renata and Alves, Tatianny Soares and Reis Vasconcellos, Luana Marotta and Sobral Silva, Leonardo Alvares and Freitas Viana, Vicente Galber and Figueredo-Silva, José and Maia Filho, Antônio Luiz Martins and Marciano, Fernanda Roberta and Lobo, Anderson Oliveira},
  title = {In Situ Printing of Polylactic Acid/Nanoceramic Filaments for the Repair of Bone Defects Using a Portable 3D Device},
  journal = {ACS Applied Materials & Interfaces},
  year = {2025},
  doi = {10.1021/acsami.4c05232}
}
Start for free →