Facile Fabrication of “Tacky”, Stretchable, and Aligned Carbon Nanotube Sheet-Based Electronics for On-Skin Health Monitoring
ACS Applied Materials & Interfaces · 2023
DOI: 10.1021/acsami.3c13541 ↗At a glance
Journal article in ACS Applied Materials & Interfaces, 2023. Written by Duy Van Nguyen and 11 co-authors. Institution: School of Engineering, University of Southern Queensland, Brisbane 4300, Queensland, Australia. Major MEDLINE topics: Nanotubes, Carbon, Wearable Electronic Devices. Cited 5 times so far (Crossref); 79 references. Funded by: Australian Government.
Abstract (original language)
Point-of-care monitoring of physiological signals such as electrocardiogram, electromyogram, and electroencephalogram is essential for prompt disease diagnosis and quick treatment, which can be realized through advanced skin-worn electronics. However, it is still challenging to design an intimate and nonrestrictive skin-contact device for physiological measurements with high fidelity and artifact tolerance. This research presents a facile method using a "tacky" surface to produce a tight interface between the ACNT skin-like electronic and the skin. The method provides the skin-worn electronic with a stretchability of up to 70% strain, greater than that of most common epidermal electrodes. Low-density ACNT bundles facilitate the infiltration of adhesive and improve the conformal contact between the ACNT sheet and the skin, while dense ACNT bundles lessen this effect. The stretchability and conformal contact allow the ACNT sheet-based electronics to create a tight interface with the skin, which enables the high-fidelity measurement of physiological signals (the Pearson's coefficient of 0.98) and tolerance for motion artifacts. In addition, our method allows the use of degradable substrates to enable reusability and degradability of the electronics based on ACNT sheets, integrating "green" properties into on-skin electronics.
Subjects
MeSH terms (MEDLINE)
Author keywords
Substances
Authors and institutions
- School of Engineering, University of Southern Queensland, Brisbane 4300, Queensland, Australia.
- Centre for Future Materials, University of Southern Queensland, Brisbane 4300, Queensland, Australia.
- School of Health and Medical Sciences, University of Southern Queensland, Brisbane 4305, Queensland, Australia.
- School of Mechanical and Manufacturing Engineering, The University of New South Wales, Sydney 1466, New South Wales, Australia.
- Queensland Micro- and Nanotechnology Centre, Griffith University, Brisbane 4111, Queensland, Australia.
- Griffith School of Engineering, Griffith University, Gold Coast 4125, Queensland, Australia.
ORCID profiles: Duy Van Nguyen, Canh-Dung Tran, Thanh Nguyen, Hung Nguyen, Pingan Song, Hoang-Phuong Phan, Dzung Viet Dao
Funding
- Australian Government
Cite
APA
Nguyen, D. V., Mills, D., Tran, C. D., Nguyen, T., Nguyen, H., Tran, T. L., Song, P., Phan, H. P., Nguyen, N. T., Dao, D. V., Bell, J., & Dinh, T. (2023). Facile Fabrication of “Tacky”, Stretchable, and Aligned Carbon Nanotube Sheet-Based Electronics for On-Skin Health Monitoring. ACS Applied Materials & Interfaces. https://doi.org/10.1021/acsami.3c13541
Vancouver
Nguyen DV, Mills D, Tran CD, Nguyen T, Nguyen H, Tran TL, et al. Facile Fabrication of “Tacky”, Stretchable, and Aligned Carbon Nanotube Sheet-Based Electronics for On-Skin Health Monitoring. ACS Applied Materials & Interfaces. 2023. doi:10.1021/acsami.3c13541
BibTeX
@article{Nguyen2023,
author = {Nguyen, Duy Van and Mills, Dean and Tran, Canh-Dung and Nguyen, Thanh and Nguyen, Hung and Tran, Thi Lap and Song, Pingan and Phan, Hoang-Phuong and Nguyen, Nam-Trung and Dao, Dzung Viet and Bell, John and Dinh, Toan},
title = {Facile Fabrication of “Tacky”, Stretchable, and Aligned Carbon Nanotube Sheet-Based Electronics for On-Skin Health Monitoring},
journal = {ACS Applied Materials & Interfaces},
year = {2023},
doi = {10.1021/acsami.3c13541}
}
EUVIMED