Design of Cathode Coating Using Niobate and Phosphate Hybrid Material for Sulfide-Based Solid-State Battery
ACS Applied Materials & Interfaces · 02.08.2023 · 15 (30) · 36086-36095
DOI: 10.1021/acsami.3c02827 ↗Kurz gefasst
Fachartikel in der Zeitschrift ACS Applied Materials & Interfaces, online erschienen am 18.07.2023. Verfasst von Yusuke Morino und 8 weiteren Autor:innen. Beteiligte Einrichtung: Consortium for Lithium Ion Battery Technology and Evaluation Center (LIBTEC) 1-8-31 Midorigaoka, Ikeda, Osaka 563-8577, Japan. Die Arbeit wurde bisher 25-mal zitiert (Crossref) und nennt 61 Literaturangaben. Gefördert von: New Energy and Industrial Technology Development Organization.
Abstract (Originalsprache)
Coating the surface of the cathode active material of all-solid-state batteries with sulfide-based solid electrolytes is key for improving and enhancing the battery performance. Although lithium niobate (LiNbO3) is one of the most representative coating materials, its low durability at a highly charged potential and high temperature is an impediment to the realization of high-performance all-solid-state batteries. In this study, we developed new hybrid coating materials consisting of lithium niobate (Li-Nb-O) and lithium phosphate (Li-P-O) and investigated the influence of the ratio of P/(Nb + P) on the durability performance. The cathode half-cells, using a sulfide-based solid electrolyte Li6PS5Cl/cathode active material, LiNi0.5Co0.2Mn0.3O2, coated with the new hybrid coating materials of LiPxNb1-xO3 (x = 0-1), were exposed to harsh conditions (60 °C and 4.55 V vs Li/Li+) for 120 h as a degradation test. P substitution resulted in higher durability and lower interfacial resistance. In particular, the hybrid coating with x = 0.5 performed better, in terms of capacity retention and interfacial resistance, than those with other compositions of niobate and phosphate. The coated cathode active materials were analyzed using various analytical techniques such as scanning electron microscopy/energy-dispersive X-ray spectroscopy, transmission electron microscopy (TEM), X-ray photoelectron spectroscopy, and X-ray absorption spectroscopy (XAS) to elucidate the improvement mechanism. Moreover, the degraded cathodes were observed using time-of-flight secondary-ion mass spectrometry, TEM/electron diffraction, and XAS. These analyses revealed that the Nb-O-P coordination in the hybrid coating material captured O by P. The coordination suppressed the release of O from the coating layer as a decomposition side reaction to realize a higher durability than that of LiNbO3.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Consortium for Lithium Ion Battery Technology and Evaluation Center (LIBTEC) 1-8-31 Midorigaoka, Ikeda, Osaka 563-8577, Japan.
- OHARA INC. 1-15-30, Oyama, Chuo-ku, Sagamihara, Kanagawa 252-5286, Japan.
- Department of Materials Science, Osaka Metropolitan University, Sakai, Osaka 599-8531, Japan.
- Department of Material Design Innovation Engineering, Graduate School of Engineering, Nagoya University, Furo-cho, Chikusa-ku, Nagoya 464-8603, Japan.
ORCID-Profile: Yusuke Morino, Yasutoshi Iriyama
Förderung
- New Energy and Industrial Technology Development Organization
Zitieren
APA
Morino, Y., Shiota, A., Kanada, S., Bong, W. S. K., Kawamoto, K., Inda, Y., Tsukasaki, H., Mori, S., & Iriyama, Y. (2023). Design of Cathode Coating Using Niobate and Phosphate Hybrid Material for Sulfide-Based Solid-State Battery. ACS Applied Materials & Interfaces, 15(30), 36086-36095. https://doi.org/10.1021/acsami.3c02827
Vancouver
Morino Y, Shiota A, Kanada S, Bong WSK, Kawamoto K, Inda Y, et al. Design of Cathode Coating Using Niobate and Phosphate Hybrid Material for Sulfide-Based Solid-State Battery. ACS Applied Materials & Interfaces. 2023;15(30):36086-36095. doi:10.1021/acsami.3c02827
BibTeX
@article{Morino2023,
author = {Morino, Yusuke and Shiota, Akihiro and Kanada, Satoshi and Bong, Willy Shun Kai and Kawamoto, Koji and Inda, Yasushi and Tsukasaki, Hirofumi and Mori, Shigeo and Iriyama, Yasutoshi},
title = {Design of Cathode Coating Using Niobate and Phosphate Hybrid Material for Sulfide-Based Solid-State Battery},
journal = {ACS Applied Materials & Interfaces},
year = {2023},
volume = {15},
number = {30},
pages = {36086--36095},
doi = {10.1021/acsami.3c02827}
}
EUVIMED