3D-Printed Porous Polymer Monoliths for Tunable Pheromone Release
ACS Applied Engineering Materials · 25.09.2026 · 4 (9) · 4751-4757
DOI: 10.1021/acsaenm.6c00625 ↗Kurz gefasst
Fachartikel in der Zeitschrift ACS Applied Engineering Materials, online erschienen am 07.09.2026. Verfasst von Benedikt Keitel und 14 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 34 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Bundesministerium für Forschung, Technologie und Raumfahrt, Toray Research Center, Joachim Herz Stiftung.
Abstract (Originalsprache)
Polymerization-induced phase separation (PIPS) in scalable, low-cost LCD-based 3D printing enables the fabrication of inherently porous monoliths with tunable properties for volatile organic compound (VOC) release. Addressing the need for tunable semiochemical release in species-specific pest control, we present a proof-of-principle study on semiochemical emission using methacrylate-based 3D-printed monoliths loaded with verbenone as a model pheromone. By systematically varying porogens (turpentine oil vs cyclohexanol/1-decanol mixture), porogen-to-monomer ratio, and pheromone loading, distinct pore regimes ranging from submicrometer networks to micrometer-scale domains were generated in 3D porous cubes with an edge length of 5 mm. Morphological characterization by scanning electron microscopy and mercury intrusion porosimetry revealed that turpentine oil-based formulations exhibit larger pore domains than cyclohexanol/1-decanol-based analogs. Furthermore, headspace thermal desorption gas chromatography−mass spectrometry measurements of the 3D porous cubes demonstrated formulation-dependent verbenone emission, with turpentine-oil-based systems exhibiting higher emission intensities than cyclohexanol/1-decanol-based analogs. Overall, larger-pore formulations were generally associated with higher verbenone emission intensities; however, remaining porogens may also contribute to the observed behavior. The presented proof-of-principle results highlight the potential of combining PIPS with LCD-based 3D printing to fabricate porous polymer dispensers with tunable semiochemical emission characteristics, while quantitative control and long-term release remain a subject of future investigation. Thus, the findings provide a foundation for future studies on structure−emission relationships and the rational design of additively manufactured, bioinspired VOC release systems with potential applications in sustainable pest management and beyond.
Förderung
- Bundesministerium für Forschung, Technologie und Raumfahrt
- Toray Research Center
- Joachim Herz Stiftung
Zitieren
APA
Keitel, B., Huber, A., Yoshida, Y., Shioji, H., Furushima, Y., Yamanaka, T., Ohkawa, T., Yoshimoto, S., Uehara, F., Hamashige, C., Nakamura, K., Uchiyama, H., Yamamoto, T., Mizaikoff, B., & Dinc, M. (2026). 3D-Printed Porous Polymer Monoliths for Tunable Pheromone Release. ACS Applied Engineering Materials, 4(9), 4751-4757. https://doi.org/10.1021/acsaenm.6c00625
Vancouver
Keitel B, Huber A, Yoshida Y, Shioji H, Furushima Y, Yamanaka T, et al. 3D-Printed Porous Polymer Monoliths for Tunable Pheromone Release. ACS Applied Engineering Materials. 2026;4(9):4751-4757. doi:10.1021/acsaenm.6c00625
BibTeX
@article{Keitel2026,
author = {Keitel, Benedikt and Huber, Amelie and Yoshida, Yuki and Shioji, Hirotaka and Furushima, Yoshitomo and Yamanaka, Toru and Ohkawa, Tomohiro and Yoshimoto, Shigeru and Uehara, Fumiya and Hamashige, Chihiro and Nakamura, Kazuya and Uchiyama, Hironobu and Yamamoto, Takashi and Mizaikoff, Boris and Dinc, Mehmet},
title = {3D-Printed Porous Polymer Monoliths for Tunable Pheromone Release},
journal = {ACS Applied Engineering Materials},
year = {2026},
volume = {4},
number = {9},
pages = {4751--4757},
doi = {10.1021/acsaenm.6c00625}
}
EUVIMED