EUVIMEDEUVIMED entdecken
Crossref

3D-Printed OsteoFlux Scaffolds with Radially Graded TPMS Structures

Miaomiao Zheng, Shiquan Shen, Yutong Chen, Shun Zhang, Jian Chao, Yan Xu iD

ACS Applied Bio Materials · 10.11.2026

DOI: 10.1021/acsabm.6c01507 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Applied Bio Materials, online erschienen am 10.11.2026. Verfasst von Miaomiao Zheng und 5 weiteren Autor:innen. Beteiligte Einrichtung: College of Mechanical Engineering, Xinjiang University, Urumqi830017, China. Die Arbeit nennt 46 Literaturangaben. Gefördert von: National Natural Science Foundation of China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In native bone, the transition from dense cortical bone to porous cancellous bone reflects a spatial coordination between mechanical support and mass transport. Inspired by this structural heterogeneity, this study proposes an OsteoFlux (OF) scaffold featuring a radially graded TPMS structure together with a corresponding 3D printing strategy. Specifically, a biomimetic TPMS scaffold design integrating a continuous pore-size gradient with an explicit gradient position constraint was developed. Fluid–structure interaction (FSI) simulations investigating the effects of TPMS topology and gradient parameters on scaffold mechanical and transport performance were performed. The results indicated that the OF scaffold (a Gyroid (G-type) scaffold with an 800–400 μm radial pore-size gradient) achieved the most favorable combination of mechanical stability and fluid transport performance. Finally, an experiment optimizing the BCP slurry system and digital light processing (DLP) printing parameters was conducted. The fabricated OF scaffold exhibited a compressive strength of 3.25 MPa, a compressive modulus of 172.55 MPa, and a permeability of 4.17 × 10–9 m2. In vitro biological evaluation demonstrated favorable cytocompatibility, along with enhanced osteogenic differentiation and matrix mineralization of mBMSCs under scaffold-conditioned culture conditions. These findings demonstrate that the proposed OF scaffold provides an effective strategy for enhancing the overall performance of porous ceramic scaffolds.

Schlagwörter

Stichwörter der Autor:innen

biomimetic scaffold designbone tissue engineeringdigital light processingradial pore-size gradienttriply periodic minimal surface

Autor:innen und Institutionen

  • College of Mechanical Engineering, Xinjiang University, Urumqi830017, China.
  • State Key Laboratory of Intelligent Manufacturing Equipment and Technology, School of Mechanical Science and Engineering, Huazhong University of Science and Technology, Wuhan430074, China.

ORCID-Profile: Yan Xu

Förderung

  • National Natural Science Foundation of China

Zitieren

APA

Zheng, M., Shen, S., Chen, Y., Zhang, S., Chao, J., & Xu, Y. (2026). 3D-Printed OsteoFlux Scaffolds with Radially Graded TPMS Structures. ACS Applied Bio Materials. https://doi.org/10.1021/acsabm.6c01507

Vancouver

Zheng M, Shen S, Chen Y, Zhang S, Chao J, Xu Y. 3D-Printed OsteoFlux Scaffolds with Radially Graded TPMS Structures. ACS Applied Bio Materials. 2026. doi:10.1021/acsabm.6c01507

BibTeX
@article{Zheng2026,
  author = {Zheng, Miaomiao and Shen, Shiquan and Chen, Yutong and Zhang, Shun and Chao, Jian and Xu, Yan},
  title = {3D-Printed OsteoFlux Scaffolds with Radially Graded TPMS Structures},
  journal = {ACS Applied Bio Materials},
  year = {2026},
  doi = {10.1021/acsabm.6c01507}
}
Kostenlos starten →