EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Temperature-Dependent Dynamic Friction of a Single Human Corneocyte at Nanoscale Contact: An Analytical Approach and Direct Measurement Using Lateral Force Microscopy for Haptic Design Insight

Perawat Boonpuek iD, Thanathip Boonmatoon, Jonathan R Felts iD

Langmuir · 2025

DOI: 10.1021/acs.langmuir.5c03556 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Langmuir, 2025. Verfasst von Perawat Boonpuek und 2 weiteren Autor:innen. Beteiligte Einrichtung: School of Manufacturing Engineering, Institute of Engineering, Suranaree University of Technology, 111 University Avenue, Suranaree Subdistrict, Muan…. Hauptthemen laut MEDLINE: Microscopy, Atomic Force, Friction, Temperature, Skin. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 85 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: J. Mike Walker '66 Department of Mechanical Engineering, Texas A&M university.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Dynamic friction between human skin and a haptic surface is known to increase with the substrate temperature. When the substrate temperature reaches 60 °C, prolonged sliding contact for just 1 min can cause damage to the outer skin surface. However, the effect of the temperature on dynamic friction at the nanoscale interface between human skin cells and a nanosized probe remains inadequately quantified. This paper presents direct measurements of the dynamic friction of human skin corneocytes as a function of the AFM nanoprobe temperature, using atomic force microscopy (AFM). The lateral force microscopy (LFM) technique with a heated tip was employed to quantify the dynamic friction force of the corneocytes under a constant normal load of 10 nN and standard relative humidity (40% RH). The temperature of the heated tip was calibrated before each LFM experiment. The friction force, derived from the LFM signal data during each temperature scan, was compared to dynamic friction calculations based on a proposed analytical model. The results show that dynamic friction increases exponentially with sliding velocity as the temperature of the heated AFM tip rises, but the rate of increase slows at very high sliding velocities. These findings suggest that, in the nanoscopic contact regime at low haptic substrate temperatures ( 35 °C) with faster sliding velocities, the finger may experience lubrication from skin hydration.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Microscopy, Atomic ForceFrictionTemperatureSkinHumansSurface Properties

Autor:innen und Institutionen

  • School of Manufacturing Engineering, Institute of Engineering, Suranaree University of Technology, 111 University Avenue, Suranaree Subdistrict, Muang, Nakhon Ratchasima 30000, Thailand.
  • Advanced Manufacturing Laboratory, J. Mike Walker '66 Department of Mechanical Engineering, College of Engineering, Texas A&M University, College Station, Texas 77843, United States.

ORCID-Profile: Perawat Boonpuek, Jonathan R Felts

Förderung

  • J. Mike Walker '66 Department of Mechanical Engineering, Texas A&M university

Zitieren

APA

Boonpuek, P., Boonmatoon, T., & Felts, J. R. (2025). Temperature-Dependent Dynamic Friction of a Single Human Corneocyte at Nanoscale Contact: An Analytical Approach and Direct Measurement Using Lateral Force Microscopy for Haptic Design Insight. Langmuir. https://doi.org/10.1021/acs.langmuir.5c03556

Vancouver

Boonpuek P, Boonmatoon T, Felts JR. Temperature-Dependent Dynamic Friction of a Single Human Corneocyte at Nanoscale Contact: An Analytical Approach and Direct Measurement Using Lateral Force Microscopy for Haptic Design Insight. Langmuir. 2025. doi:10.1021/acs.langmuir.5c03556

BibTeX
@article{Boonpuek2025,
  author = {Boonpuek, Perawat and Boonmatoon, Thanathip and Felts, Jonathan R},
  title = {Temperature-Dependent Dynamic Friction of a Single Human Corneocyte at Nanoscale Contact: An Analytical Approach and Direct Measurement Using Lateral Force Microscopy for Haptic Design Insight},
  journal = {Langmuir},
  year = {2025},
  doi = {10.1021/acs.langmuir.5c03556}
}
Kostenlos starten →