EUVIMEDEUVIMED entdecken
Crossref

Influence of Resin Color and Printer Brand on Emissions from Stereolithography (SLA) 3-D Printers

Aleksandr B. Stefaniak, Elizabeth D. Brusak, Sayon Robinson, Lauren N. Bowers, Matthew Roemer, Joanna Matheson, Sherri A. Friend, M. Abbas Virji

ACS Chemical Health & Safety · 28.07.2025 · 32 (4) · 504-512

DOI: 10.1021/acs.chas.5c00076 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Chemical Health & Safety, online erschienen am 04.07.2025. Verfasst von Aleksandr B. Stefaniak und 7 weiteren Autor:innen. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 44 Literaturangaben.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Vat photopolymerization (VP) is an additive manufacturing process that uses light to harden resin and build a 3-dimensional shape. Stereolithography (SLA) printing is a variant of VP that uses a laser beam as the light source to initiate a polymerization reaction. During SLA printing, particles and gases can be emitted into the air; however, factors that influence emissions are poorly understood for this technology. Emissions from two brands of SLA printers from different manufacturers (herein termed A and B) were measured using real-time (particle number and size, total volatile organic compound [TVOC] concentration) and time-integrated (aldehydes, acrylates, aromatics, alkanes, butylated hydroxy toluene, and elements) techniques in an environmental test chamber. Three colors of resins (black, clear, and gray), all from the same manufacturer, were tested on each printer. All statistical comparisons used a significance level of 0.05. Printer brand strongly influenced the emission yields. Printer A had significantly higher particle number yield, smaller particle size, and higher 2-hydroxyethyl methacrylate (2-HEMA) and 2-hydroxypropyl methacrylate yields for all resin colors compared with printer B. There were also significant differences between brands in yield values for several aldehydes (acetaldehyde, butyraldehyde, hexaldehyde, isovaleraldehyde, o,m,p-tolualdehyde, and propionaldehyde). Resin color had a minor influence on yields for particle number, some aldehydes, and 2-HEMA for printer A only. The strong influence of printer brand on emissions was partially explained by printer configuration, i.e., printer A had a built-in resin heater, whereas printer B did not. Emission yields of organic chemicals were not always higher for printer A compared with printer B, which indicated that other factors also influenced emissions. Improved understanding of factors that influence emissions from SLA printers is critical for developing exposure mitigation strategies using a hierarchy of controls.

Zitieren

APA

Stefaniak, A. B., Brusak, E. D., Robinson, S., Bowers, L. N., Roemer, M., Matheson, J., Friend, S. A., & Virji, M. A. (2025). Influence of Resin Color and Printer Brand on Emissions from Stereolithography (SLA) 3-D Printers. ACS Chemical Health & Safety, 32(4), 504-512. https://doi.org/10.1021/acs.chas.5c00076

Vancouver

Stefaniak AB, Brusak ED, Robinson S, Bowers LN, Roemer M, Matheson J, et al. Influence of Resin Color and Printer Brand on Emissions from Stereolithography (SLA) 3-D Printers. ACS Chemical Health & Safety. 2025;32(4):504-512. doi:10.1021/acs.chas.5c00076

BibTeX
@article{Stefaniak2025,
  author = {Stefaniak, Aleksandr B. and Brusak, Elizabeth D. and Robinson, Sayon and Bowers, Lauren N. and Roemer, Matthew and Matheson, Joanna and Friend, Sherri A. and Virji, M. Abbas},
  title = {Influence of Resin Color and Printer Brand on Emissions from Stereolithography (SLA) 3-D Printers},
  journal = {ACS Chemical Health & Safety},
  year = {2025},
  volume = {32},
  number = {4},
  pages = {504--512},
  doi = {10.1021/acs.chas.5c00076}
}
Kostenlos starten →