3D-printing bauxite residue/fly ash-containing geopolymers as promising metal sorbents for water treatment
Waste Management · 2024-12 · 190 · 35-44
DOI: 10.1016/j.wasman.2024.09.007 ↗Kurz gefasst
Fachartikel in der Zeitschrift Waste Management, 2024-12. Verfasst von Mariana M Almeida und 5 weiteren Autor:innen. Beteiligte Einrichtung: Dept. of Materials and Ceramic Engineering/CICECO-Aveiro Institute of Materials, University of Aveiro, Campus Universitário de Santiago, 3810-193 Ave…. Hauptthemen laut MEDLINE: Coal Ash, Printing, Three-Dimensional, Water Purification, Aluminum Oxide. Die Arbeit wurde bisher 28-mal zitiert (Crossref) und nennt 48 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: Horizon Europe, Foundation for Science and Technology.
Abstract (Originalsprache)
Herein, we demonstrate for the first time the feasibility of employing significant amounts (up to 80 wt%) of unexplored industrial wastes (red mud and biomass fly ash) in the production of highly porous 3D-printed geopolymer lattices envisioned for wastewater treatment applications. This without compromising the mechanical performance of the geopolymers relative to those obtained using commercial precursors. The impact of the fly ash incorporation content in the fresh-state (calorimetric and reological characterization) and hardened-state (porosity and mechanical strength) properties of the produced structures was evaluated. Moreover, the influence of key printing parameters, including nozzle diameter and geometry alignment, on the resulting properties of the lattices was also evaluated. The most promising compositions were then evaluated as lead sorbents under continuous flow. The waste-based 3D-printed lattices showed remarkable adsorption ability reaching >95 % removal efficiency after 2 h. This sustainable strategy is in line with the United Nations sustainable development goals and the transition to a circular economy, reducing the consumption of natural resources and simultaneously contributing to reducing water pollution.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Dept. of Materials and Ceramic Engineering/CICECO-Aveiro Institute of Materials, University of Aveiro, Campus Universitário de Santiago, 3810-193 Aveiro, Portugal. Electronic address: mmalmeida@ua.pt.
- Dept. of Chemistry/CICECO-Aveiro Institute of Materials, University of Aveiro, Campus Universitário de Santiago, 3810-193 Aveiro, Portugal.
- Dept. of Materials and Ceramic Engineering/CICECO-Aveiro Institute of Materials, University of Aveiro, Campus Universitário de Santiago, 3810-193 Aveiro, Portugal.
Förderung
- Horizon Europe
- Foundation for Science and Technology
Zitieren
APA
Almeida, M. M., Gonçalves, N. P. F., Gameiro, T., Alves, Z., Labrincha, J. A., & Novais, R. M. (2024). 3D-printing bauxite residue/fly ash-containing geopolymers as promising metal sorbents for water treatment. Waste Management, 190, 35-44. https://doi.org/10.1016/j.wasman.2024.09.007
Vancouver
Almeida MM, Gonçalves NPF, Gameiro T, Alves Z, Labrincha JA, Novais RM. 3D-printing bauxite residue/fly ash-containing geopolymers as promising metal sorbents for water treatment. Waste Management. 2024;190:35-44. doi:10.1016/j.wasman.2024.09.007
BibTeX
@article{Almeida2024,
author = {Almeida, Mariana M and Gonçalves, Nuno P F and Gameiro, Tânia and Alves, Zélia and Labrincha, João A and Novais, Rui M},
title = {3D-printing bauxite residue/fly ash-containing geopolymers as promising metal sorbents for water treatment},
journal = {Waste Management},
year = {2024},
volume = {190},
pages = {35--44},
doi = {10.1016/j.wasman.2024.09.007}
}
EUVIMED