EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC 4.0

Questioning the ASTM G32-16 (stationary specimen) standard cavitation erosion test

Matevž Dular, Guillermo Enrique Barragan Montalvo, Marko Hočevar, Lovrenc Novak, Claus Dieter Ohl, Martin Petkovsek

Ultrasonics Sonochemistry · 2024-07 · 107 · 106930

DOI: 10.1016/j.ultsonch.2024.106930 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Ultrasonics Sonochemistry, 2024-07. Verfasst von Matevž Dular und 5 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Mechanical Engineering, University of Ljubljana, Askerceva 6, 1000 Ljubljana, SI, Slovenia; Institute for Physics, Otto von Guerricke Univ…. Die Arbeit wurde bisher 22-mal zitiert (Crossref) und nennt 46 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Cavitation erosion is one of the most severe problems encountered in hydraulic turbomachinery. When testing the materials, the engineers usually rely on standardized procedures. The most common one being the vibratory ASTM G-32 test, which offers two possibilities of performing the test - the direct, where the specimen is attached to the ultrasonic device and the indirect, where the specimen is stationary and exposed to the ultrasonic horn, positioned just 0.5 mm from it. The erosion rates from the two are significantly different and a question may be asked if they are at all comparable and further on are they comparable to the "real-life" hydrodynamic cavitation which occurs in turbomachinery. In this study we performed erosion tests on a stationary specimen where the gap between the specimen and the horn was varied from 0.3 to 4 mm. In addition, we used high speed visualization to observe the cavitation in the gap. We observed that the cavitation erosion rate strongly depends on the gap. From visualization we see that the cavitation dynamics significantly changes in a small gap, leading to a large, but 2-dimensional cavitation bubbles which collapse very slowly, compared to the small spherical ones in a larger gap. We investigated the probability of shock wave occurrence and derived a very simple model, which gives accurate qualitative predictions of experimental data. Finally, the study puts into question the validity of ASTM G32 test - the most common approach used in engineering today.

Schlagwörter

Stichwörter der Autor:innen

BubbleCavitationErosionG32 standard

Autor:innen und Institutionen

  • Faculty of Mechanical Engineering, University of Ljubljana, Askerceva 6, 1000 Ljubljana, SI, Slovenia; Institute for Physics, Otto von Guerricke University, Universitätsplatz 2, 39106 Magdeburg, DE, Germany. Electronic…
  • Escuela Politécnica Nacional, Av. Ladrón de Guevara E11-253, Quito 170525, Ecuador.
  • Faculty of Mechanical Engineering, University of Ljubljana, Askerceva 6, 1000 Ljubljana, SI, Slovenia.
  • Institute for Physics, Otto von Guerricke University, Universitätsplatz 2, 39106 Magdeburg, DE, Germany.

Zitieren

APA

Dular, M., Montalvo, G. E. B., Hočevar, M., Novak, L., Ohl, C. D., & Petkovsek, M. (2024). Questioning the ASTM G32-16 (stationary specimen) standard cavitation erosion test. Ultrasonics Sonochemistry, 107, 106930. https://doi.org/10.1016/j.ultsonch.2024.106930

Vancouver

Dular M, Montalvo GEB, Hočevar M, Novak L, Ohl CD, Petkovsek M. Questioning the ASTM G32-16 (stationary specimen) standard cavitation erosion test. Ultrasonics Sonochemistry. 2024;107:106930. doi:10.1016/j.ultsonch.2024.106930

BibTeX
@article{Dular2024,
  author = {Dular, Matevž and Montalvo, Guillermo Enrique Barragan and Hočevar, Marko and Novak, Lovrenc and Ohl, Claus Dieter and Petkovsek, Martin},
  title = {Questioning the ASTM G32-16 (stationary specimen) standard cavitation erosion test},
  journal = {Ultrasonics Sonochemistry},
  year = {2024},
  volume = {107},
  pages = {106930},
  doi = {10.1016/j.ultsonch.2024.106930}
}
Kostenlos starten →