EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

How to convert a 3D printer to a personal automated liquid handler for life science workflows

Dulguunnaran Naranbat, Benjamin Phelps, John Murphy, Anubhav Tripathi

SLAS Technology · 2025-02 · 30 · 100239

DOI: 10.1016/j.slast.2024.100239 ↗

Kurz gefasst

Fachartikel in der Zeitschrift SLAS Technology, 2025-02. Verfasst von Dulguunnaran Naranbat und 3 weiteren Autor:innen. Beteiligte Einrichtung: Center for Biomedical Engineering, School of Engineering, Brown University, Providence, RI 02912, USA. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Automation, Laboratory, Workflow. Die Arbeit wurde bisher 15-mal zitiert (Crossref) und nennt 73 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: Brown University, Revvity Health Sciences Inc.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Automated liquid handlers are fundamental in modern life science laboratories, yet their high costs and large footprints often limit accessibility for smaller labs. This study presents an innovative approach to decentralizing a liquid handling system by converting a low-cost 3D printer into a customizable and accurate liquid handler. The Personal Automated Liquid Handler (PALH) system, costing ∼$400, incorporates a single-channel pipet, custom 3D-printed components, and open-source software for personalized workflows, allowing researchers to build and modify the system for specific experimental needs. The PALH system was evaluated through common life science assays, including preparing real-time PCR samples, end-point PCR with novel pipet-based downstream purification, and genomic DNA extraction from peripheral whole blood. In real-time PCR experiments targeting the YWHAZ gene, the PALH system demonstrated comparable performance to manual preparation across DNA quantities (1 pg to 100 ng). For end-point PCR, the PALH successfully amplified and purified 204 bp and 406 bp amplicons from a pUC19 vector, yielding concentrations similar to manual methods (5.43 ± 0.85 ng/µL vs. 2.10 ± 0.16 ng/µL for 204 bp; 3.74 ± 2.13 ng/µL vs. 1.51 ± 0.15 ng/µL for 406 bp, respectively). In genomic DNA extraction from whole blood, the PALH system achieved comparable DNA yields to manual extraction (49.52 ± 3.13 ng/µL vs. 48.62 ± 5.9 ng/µL), although at higher purity (260/280 ratio of 1.83 ± 0.07 vs. 1.92 ± 0.03), although both are at acceptable ranges. The open-source nature of the PALH system hopefully encourages further community-driven improvements and protocol sharing, fostering innovation and collaboration within the scientific community. As laboratory automation advances, the PALH system could be crucial in democratizing access to high-quality automated liquid handling, particularly in resource-limited settings.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalAutomation, LaboratoryWorkflowHumansDNA

Stichwörter der Autor:innen

3D printerLab automationLiquid handling systemLow-cost liquid handlerOpen-source developmentPipet-based magnetic nucleic acid purification

Substanzen

DNA

Autor:innen und Institutionen

  • Center for Biomedical Engineering, School of Engineering, Brown University, Providence, RI 02912, USA.
  • Center for Biomedical Engineering, School of Engineering, Brown University, Providence, RI 02912, USA. Electronic address: anubhav_tripathi@brown.edu.

Förderung

  • Brown University
  • Revvity Health Sciences Inc

Zitieren

APA

Naranbat, D., Phelps, B., Murphy, J., & Tripathi, A. (2025). How to convert a 3D printer to a personal automated liquid handler for life science workflows. SLAS Technology, 30, 100239. https://doi.org/10.1016/j.slast.2024.100239

Vancouver

Naranbat D, Phelps B, Murphy J, Tripathi A. How to convert a 3D printer to a personal automated liquid handler for life science workflows. SLAS Technology. 2025;30:100239. doi:10.1016/j.slast.2024.100239

BibTeX
@article{Naranbat2025,
  author = {Naranbat, Dulguunnaran and Phelps, Benjamin and Murphy, John and Tripathi, Anubhav},
  title = {How to convert a 3D printer to a personal automated liquid handler for life science workflows},
  journal = {SLAS Technology},
  year = {2025},
  volume = {30},
  pages = {100239},
  doi = {10.1016/j.slast.2024.100239}
}
Kostenlos starten →