EUVIMEDEUVIMED entdecken
Crossref

Effect of postpolymerization on the wear behavior of additively manufactured definitive crown resins

Merve Soydan, Taha Yasar Manav

The Journal of Prosthetic Dentistry · 2026

DOI: 10.1016/j.prosdent.2026.07.007 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2026. Verfasst von Merve Soydan und 1 weiteren Autor:innen. Beteiligte Einrichtung: Research Assistant, Department of Prosthodontics, Faculty of Dentistry, Mustafa Kemal University, Antakya, Hatay, Turkey. Hauptthemen laut MEDLINE: Composite Resins, Crowns, Dental Restoration Wear, Dental Materials. Die Arbeit nennt 41 Literaturangaben. Gefördert von: Hatay Mustafa Kemal University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: Additively manufactured definitive crown ceramic-reinforced composite (DC-CRC) resin materials have been increasingly used in clinical dentistry. However, their mechanical performance depends on postpolymerization parameters. Limited evidence is available regarding the influence of different postpolymerization techniques on the wear behavior of DC-CRC materials. PURPOSE: The purpose of this in vitro study was to evaluate the effects of several postpolymerization techniques and durations on the wear volume of additively manufactured DC-CRC specimens after thermomechanical aging and to compare these outcomes with those of a subtractively manufactured hybrid ceramic. MATERIAL AND METHODS: Disk-shaped specimens (Ø12×2 mm) were digitally designed and fabricated either from a hybrid ceramic block (Vita Enamic) by milling (Group VE, n=10) or from definitive crown resin (Saremco Crowntec) using a digital light processing (DLP) 3-dimensional (3D) printer (n=50). Printed specimens were assigned to 5 postpolymerization protocols: ultraviolet (UV) light polymerization for 30 minutes (Group Sx1), UV-light polymerization for 2×30 minutes (Group Sx2), otoflash polymerization in a nitrogen atmosphere using 2×2000 flashes (Group Nx1), otoflash polymerization in a nitrogen atmosphere using 4×2000 flashes (Group Nx2), and light-emitting diode (LED) light polymerization for 2×40 seconds (Group LED). All specimens were finished and polished according to the manufacturer's instructions and subjected to thermomechanical aging in a mastication simulator (50 N, 240 000 cycles, 5 to 55 °C). Pre-aging and post-aging digital scans were obtained with a laboratory scanner. Wear volume (mm³) was calculated by aligning STL files and performing a 3D analysis. Statistical evaluation was performed using 1-way ANOVA, followed by the Tukey post hoc test for multiple comparisons (α=.05). RESULTS: A significant difference in wear volume was found among the groups (P .05). LED-polymerized specimens exhibited significantly greater wear than VE. Postpolymerization in the nitrogen atmosphere groups (Nx1 and Nx2) showed wear volumes comparable to those of the hybrid ceramic. CONCLUSIONS: Postpolymerization techniques influenced the wear resistance of additively manufactured DC-CRC materials. Polymerization in a nitrogen atmosphere improved wear performance compared with that of subtractively manufactured hybrid ceramic. Extending polymerization duration showed no significant differences in wear within each method; however, prolonged polymerization in a nitrogen atmosphere showed better outcomes than standard UV-light polymerization. Postpolymerization in a nitrogen atmosphere may therefore enhance the clinical durability of 3D printed definitive resin crowns, although long-term and clinical investigations remain necessary.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Composite ResinsCrownsDental Restoration WearDental MaterialsPolymerizationCeramicsMaterials TestingIn Vitro TechniquesSurface PropertiesPrinting, Three-DimensionalDental Stress AnalysisHumansMethacrylatesSilicates

Substanzen

Composite ResinsDental MaterialsVITA EnamicMethacrylatesSilicates

Autor:innen und Institutionen

  • Research Assistant, Department of Prosthodontics, Faculty of Dentistry, Mustafa Kemal University, Antakya, Hatay, Turkey.
  • Assistant Professor, Department of Prosthodontics, Faculty of Dentistry, Mustafa Kemal University, Antakya, Hatay, Turkey. Electronic address: tahamanav@gmail.com.

Förderung

  • Hatay Mustafa Kemal University

Zitieren

APA

Soydan, M., & Manav, T. Y. (2026). Effect of postpolymerization on the wear behavior of additively manufactured definitive crown resins. The Journal of Prosthetic Dentistry. https://doi.org/10.1016/j.prosdent.2026.07.007

Vancouver

Soydan M, Manav TY. Effect of postpolymerization on the wear behavior of additively manufactured definitive crown resins. The Journal of Prosthetic Dentistry. 2026. doi:10.1016/j.prosdent.2026.07.007

BibTeX
@article{Soydan2026,
  author = {Soydan, Merve and Manav, Taha Yasar},
  title = {Effect of postpolymerization on the wear behavior of additively manufactured definitive crown resins},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2026},
  doi = {10.1016/j.prosdent.2026.07.007}
}
Kostenlos starten →