EUVIMEDEUVIMED entdecken
Crossref

Influence of 3D printing parameters on surface roughness and stainability of a denture base resin: An in vitro study

Hamile Emanuella do Carmo Viotto, Larianne de Sousa Moisés, Sabrina Romão Gonçalves Coelho, Bruna Gazito Dias, Raphael Freitas de Souza, Ana Carolina Pero

The Journal of Prosthetic Dentistry · 2025-11 · 134 (5) · 1965.e1-1965.e7

DOI: 10.1016/j.prosdent.2025.07.025 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2025-11. Verfasst von Hamile Emanuella do Carmo Viotto und 5 weiteren Autor:innen. Beteiligte Einrichtung: Doctoral student, Department of Dental Materials and Prosthodontics, São Paulo State University (UNESP), Araraquara Dental School, Campus of Araraqua…. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Denture Bases, Dental Materials. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 54 Literaturangaben. Gefördert von: Universidade de São Paulo, Fundação de Amparo à Pesquisa do Estado de São Paulo.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: Liquid crystal display (LCD) printing systems have the advantages of lower costs, higher printing speed, and the ability to use the same resins as those used in digital light processing (DLP) systems. However, the effect of the printing angles on the properties of a denture base resin printed using LCD remains unknown. PURPOSE: The purpose of this in vitro study was to compare printing systems DLP and LCD and printing angles (0-, 45-, and 90 degrees) on the surface roughness (Ra) and stainability (ΔE00) of a 3-dimensionally (3D) printed denture base resin after immersion in coffee over time. MATERIAL AND METHODS: Disk-shaped specimens (N=72, Ø10×1.2 mm, n=12 per group) were printed using a 3D printed denture base resin (priZma 3D Bio Denture) and LCD or DLP printers at 0-, 45-, or 90 degrees. All specimens were thermocycled for 5000 cycles (5 and 55 °C). Color differences (ΔE00) were calculated using the CIEDE2000 formula. Ra and ΔE00 were measured before and after coffee immersion for 1 month, 3 months, 6 months, 12 months, 36 months, and 60 months. For ΔE00, generalized estimating equations (GEEs) were performed and a 3-way mixed-model ANOVA was used for Ra. The post hoc Bonferroni test was performed for multiple comparisons of means (α=.05 for all analyses). RESULTS: Stainability was higher for DLP ΔE00 2.86 (CI 2.52 to 3.20) than LCD ΔE00 1.95 (CI 1.61 to 2.29) (P

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalDenture BasesDental MaterialsSurface PropertiesIn Vitro TechniquesColorHumansMaterials TestingCoffeeAcrylic Resins

Substanzen

CoffeeAcrylic ResinsDental Materials

Autor:innen und Institutionen

  • Doctoral student, Department of Dental Materials and Prosthodontics, São Paulo State University (UNESP), Araraquara Dental School, Campus of Araraquara, Araraquara, SP, Brazil.
  • Master's student, Department of Dental Materials and Prosthodontics, São Paulo State University (UNESP), Araraquara Dental School, Campus of Araraquara, Araraquara, SP, Brazil.
  • Undergraduate student, São Paulo State University (UNESP), Araraquara Dental School, Campus of Araraquara, Araraquara, SP, Brazil.
  • Associate Professor, Faculty of Dental Medicine, Université Laval, Quebec, Canada.
  • Associate Professor, Department of Dental Materials and Prosthodontics, São Paulo State University (UNESP), Araraquara Dental School, Campus of Araraquara, Araraquara, SP, Brazil. Electronic address: ana.pero@unesp.br.

Förderung

  • Universidade de São Paulo
  • Fundação de Amparo à Pesquisa do Estado de São Paulo

Zitieren

APA

Viotto, H. E. D. C., Moisés, L. S., Coelho, S. R. G., Dias, B. G., de Souza, R. F., & Pero, A. C. (2025). Influence of 3D printing parameters on surface roughness and stainability of a denture base resin: An in vitro study. The Journal of Prosthetic Dentistry, 134(5), 1965.e1-1965.e7. https://doi.org/10.1016/j.prosdent.2025.07.025

Vancouver

Viotto HEDC, Moisés LS, Coelho SRG, Dias BG, de Souza RF, Pero AC. Influence of 3D printing parameters on surface roughness and stainability of a denture base resin: An in vitro study. The Journal of Prosthetic Dentistry. 2025;134(5):1965.e1-1965.e7. doi:10.1016/j.prosdent.2025.07.025

BibTeX
@article{Viotto2025,
  author = {Viotto, Hamile Emanuella do Carmo and Moisés, Larianne de Sousa and Coelho, Sabrina Romão Gonçalves and Dias, Bruna Gazito and de Souza, Raphael Freitas and Pero, Ana Carolina},
  title = {Influence of 3D printing parameters on surface roughness and stainability of a denture base resin: An in vitro study},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2025},
  volume = {134},
  number = {5},
  pages = {1965.e1--1965.e7},
  doi = {10.1016/j.prosdent.2025.07.025}
}
Kostenlos starten →