EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of 3D printed and milled zirconia on the adhesion and viability of keratinocytes: An in vitro study

Iris Frasheri, Redina Boysen, Jörg Lüchtenborg, Nicolai Miosge, Matthias Folwaczny, Falk Schwendicke, Olivia Hoefer, Andreas Keßler

The Journal of Prosthetic Dentistry · 2025

DOI: 10.1016/j.prosdent.2025.03.020 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2025. Verfasst von Iris Frasheri und 7 weiteren Autor:innen. Beteiligte Einrichtung: Associate Professor, Department of Conservative Dentistry and Periodontology, University Hospital, LMU Munich, Munich, Germany. Hauptthemen laut MEDLINE: Keratinocytes, Zirconium, Cell Adhesion, Printing, Three-Dimensional. Die Arbeit nennt 46 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: The biocompatibility and cell response of additively manufactured ceramics, important for long-term clinical success, require additional investigation. PURPOSE: The purpose of this in vitro study was to compare the biocompatibility and cell response of human gingival keratinocytes with 3-dimensionally (3D) printed and conventionally milled zirconia. MATERIAL AND METHODS: Cylindrical specimens of 3D printed and milled zirconia were prepared, and immortalized human gingival keratinocytes (IHGKs) were cultured on specimens of these materials. Cells cultured only in growth medium were the control. Cell adhesion, viability, and morphology were assessed by using water-soluble tetrazolium (WST-1) assays and scanning electron microscopy (SEM) of the disks after culturing. Eluates from the zirconia specimens were collected and tested to assess potential cytotoxicity over time and surface roughness measured by laser scanning microscopy. For cell adhesion, an independent t test for 2-samples with unequal variances (Welch t test) was performed. For the cytotoxicity tests, differences between groups were analyzed using the post hoc test for multiple comparisons with the Bonferroni correction (α=.05). RESULTS: After 24 hours, no significant difference in keratinocyte adhesion was found between 3D printed and milled zirconia (P>.05). Cell viability assays showed that, while both materials exhibited lower viability compared with the control, 3D printed zirconia displayed significantly reduced cell viability after 96 hours compared with milled zirconia (P

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

KeratinocytesZirconiumCell AdhesionPrinting, Three-DimensionalBiocompatible MaterialsHumansCell SurvivalMicroscopy, Electron, ScanningSurface PropertiesIn Vitro TechniquesGingivaMaterials TestingCells, Cultured

Substanzen

Zirconiumzirconium oxideBiocompatible Materials

Autor:innen und Institutionen

  • Associate Professor, Department of Conservative Dentistry and Periodontology, University Hospital, LMU Munich, Munich, Germany.
  • Postdoctoral Researcher, Department of Conservative Dentistry and Periodontology, University Hospital, LMU Munich, Munich, Germany.
  • Assistant Professor, Department of Prosthetic Dentistry, Center for Dental Medicine, Medical Center - University of Freiburg, Faculty of Medicine, University of Freiburg, Freiburg im Breisgau, Germany.
  • Full Professor, Department of Conservative Dentistry and Periodontology, University Hospital, LMU Munich, Munich, Germany.
  • Full Professor and Department Head, Department of Conservative Dentistry and Periodontology, University Hospital, LMU Munich, Munich, Germany.
  • Associate Professor, Department of Prosthetic Dentistry, Center for Dental Medicine, Medical Center - University of Freiburg, Faculty of Medicine, University of Freiburg, Freiburg im Breisgau, Germany; and Associate Pro…

Zitieren

APA

Frasheri, I., Boysen, R., Lüchtenborg, J., Miosge, N., Folwaczny, M., Schwendicke, F., Hoefer, O., & Keßler, A. (2025). Influence of 3D printed and milled zirconia on the adhesion and viability of keratinocytes: An in vitro study. The Journal of Prosthetic Dentistry. https://doi.org/10.1016/j.prosdent.2025.03.020

Vancouver

Frasheri I, Boysen R, Lüchtenborg J, Miosge N, Folwaczny M, Schwendicke F, et al. Influence of 3D printed and milled zirconia on the adhesion and viability of keratinocytes: An in vitro study. The Journal of Prosthetic Dentistry. 2025. doi:10.1016/j.prosdent.2025.03.020

BibTeX
@article{Frasheri2025,
  author = {Frasheri, Iris and Boysen, Redina and Lüchtenborg, Jörg and Miosge, Nicolai and Folwaczny, Matthias and Schwendicke, Falk and Hoefer, Olivia and Keßler, Andreas},
  title = {Influence of 3D printed and milled zirconia on the adhesion and viability of keratinocytes: An in vitro study},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2025},
  doi = {10.1016/j.prosdent.2025.03.020}
}
Kostenlos starten →