EUVIMEDEUVIMED entdecken
Vergleichsstudie

Analysis of implant‐supported cantilever fixed partial denture: An in vitro comparative study on vertical misfit, stress distribution, and cantilever fracture strength

Raniel Fernandes Peixoto iD, Bruna Santos Honório Tonin iD, Lívia Maria Sales Pinto-Fiamengui iD, Karina Mattes Freitas-Pontes iD, Rômulo Rocha Regis iD, Maria da Glória Chiarello de Mattos

Journal of Prosthodontics · 2024

DOI: 10.1111/jopr.13739 ↗

Kurz gefasst

Vergleichsstudie in der Zeitschrift Journal of Prosthodontics, 2024. Verfasst von Raniel Fernandes Peixoto und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Restorative Dentistry, Faculty of Pharmacy, Dentistry and Nursing, Federal University of Ceará (FFOE/UFC), Fortaleza, Ceará, Brazil. Hauptthemen laut MEDLINE: Denture, Partial, Fixed, Dental Stress Analysis, Dental Prosthesis, Implant-Supported, Dental Restoration Failure. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 47 Literaturangaben. Gefördert von: São Paulo Research Foundation, Brazil, NEODENT, Straumann Group Brand, Brazil.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

To evaluate the vertical misfit, stress distribution around dental implants, and cantilever fracture strength of 3‐unit implant‐supported cantilever fixed partial dentures (FPDs) using frameworks made from different materials and manufacturing techniques. Materials and Methods Forty FPDs were fabricated and divided into 5 groups ( n = 8) based on the framework material used: LAS Co‐Cr (Conventional casting—laser welding); TIG Co‐Cr (Conventional casting –TIG welding); OP Co‐Cr (Conventional casting—one‐piece); CAD Co‐Cr (CAD‐CAM); and CAD Zr (CAD‐CAM ZrO 2 ). The vertical misfit was evaluated before porcelain application (T1) and before (T2), and after thermomechanical cycling (T3) by stereomicroscopy. Cantilever fracture strength was tested with a 50 kN (5000 kgf) load cell at a crosshead speed of 0.5 mm/min. Qualitative and quantitative photoelastic analysis was performed to evaluate stress distribution at seven specific points in five FPDs ( n = 1/group) subjected to occlusal loading.

Results

Only the molar showed interaction among the three factors (G × S × T; F (20.932) = 1.630; p = 0.044). Thermomechanical cycling (T2 vs. T3) had a significant effect on intra‐group vertical misfit in molar, especially in LAS Co‐Cr (Δ = 5.87; p = 0.018) and OP Co‐Cr (Δ = 5.39; p = 0.007), with no significant effect in premolar ( p > 0.05). Ceramic application combined with thermomechanical cycling (T1 vs. T3) caused a significant intra‐group increase in vertical misfit in all groups, both in the molar and premolar ( p < 0.05). OP Co‐Cr was associated with greater vertical misfit and stress concentration. Frameworks manufactured by the CAD‐CAM system exhibited lower vertical misfit and better stress distribution. FPDs with metal frameworks (>410.83 ± 72.26 N) showed significantly higher fracture strength ( p < 0.05) than zirconia (277.47 ± 39.10 N), and the first signs of ceramic veneering fracture were observed around 900 N.

Conclusions

FPDs with frameworks manufactured using a CAD‐CAM system appear to be associated with lower vertical misfit and better stress distribution, although the section of the frameworks followed by welding may be a viable alternative. In addition, metal frameworks exhibit high fracture strength.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Denture, Partial, FixedDental Stress AnalysisDental Prosthesis, Implant-SupportedDental Restoration FailureHumansIn Vitro TechniquesDenture DesignMaterials TestingZirconiumComputer-Aided DesignDental PorcelainDental Casting Technique

Stichwörter der Autor:innen

biomechanicsdental implantsdental prosthesisimplant‐supported prosthesispassive fit

Substanzen

Zirconiumzirconium oxideDental Porcelain

Autor:innen und Institutionen

  • Department of Restorative Dentistry, Faculty of Pharmacy, Dentistry and Nursing, Federal University of Ceará (FFOE/UFC), Fortaleza, Ceará, Brazil.
  • Department of Dental Materials and Prosthodontics, Ribeirão Preto School of Dentistry, University of São Paulo (FORP/USP), Ribeirão Preto, São Paulo, Brazil.

ORCID-Profile: Raniel Fernandes Peixoto, Bruna Santos Honório Tonin, Lívia Maria Sales Pinto-Fiamengui, Karina Mattes Freitas-Pontes, Rômulo Rocha Regis

Förderung

  • São Paulo Research Foundation, Brazil
  • NEODENT, Straumann Group Brand, Brazil

Zitieren

APA

Peixoto, R. F., Tonin, B. S. H., Pinto-Fiamengui, L. M. S., Freitas-Pontes, K. M., Regis, R. R., & Mattos, M. D. G. C. (2024). Analysis of implant‐supported cantilever fixed partial denture: An in vitro comparative study on vertical misfit, stress distribution, and cantilever fracture strength. Journal of Prosthodontics. https://doi.org/10.1111/jopr.13739

Vancouver

Peixoto RF, Tonin BSH, Pinto-Fiamengui LMS, Freitas-Pontes KM, Regis RR, Mattos MDGC. Analysis of implant‐supported cantilever fixed partial denture: An in vitro comparative study on vertical misfit, stress distribution, and cantilever fracture strength. Journal of Prosthodontics. 2024. doi:10.1111/jopr.13739

BibTeX
@article{Peixoto2024,
  author = {Peixoto, Raniel Fernandes and Tonin, Bruna Santos Honório and Pinto-Fiamengui, Lívia Maria Sales and Freitas-Pontes, Karina Mattes and Regis, Rômulo Rocha and Mattos, Maria da Glória Chiarello de},
  title = {Analysis of implant‐supported cantilever fixed partial denture: An in vitro comparative study on vertical misfit, stress distribution, and cantilever fracture strength},
  journal = {Journal of Prosthodontics},
  year = {2024},
  doi = {10.1111/jopr.13739}
}
Kostenlos starten →