EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Investigating the influence of infill pattern and layer height on the mechanical and bonding behavior of additively manufactured PEEK for dental applications

Almira Ada Diken Türksayar, Sandra Schulnig, Sebastian Spintzyk, İrem Beril Yeşil Kurt

The Journal of Prosthetic Dentistry · 2025

DOI: 10.1016/j.prosdent.2025.03.010 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2025. Verfasst von Almira Ada Diken Türksayar und 3 weiteren Autor:innen. Beteiligte Einrichtung: Associate Professor and Department Head, Department of Prosthodontics, Biruni University, Faculty of Dentistry, İstanbul, Turkey; and Guest Researche…. Hauptthemen laut MEDLINE: Polyethylene Glycols, Ketones, Dental Bonding, Dental Materials. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 54 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Evonik Industries.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: Current knowledge regarding the influence of infill pattern and layer height on the flexural and shear bond strength of polyetheretherketone (PEEK) manufactured via fused filament fabrication technology remains limited. PURPOSE: The purpose of this in vitro study was to investigate the impact of infill pattern and layer height on the shear bond strength (SBS) and the flexural strength (FS) of additively manufactured PEEK bars and disks relevant to dental applications. MATERIAL AND METHODS: The PEEK specimens were prepared in 9 groups (n=10), whereby different layer heights (0.1, 0.2, and 0.3 mm) and different infill patterns (±30, ±45 lines, concentric) were used. The surface roughness (Ra) was recorded with a confocal microscope. For the SBS test, resin composites were applied on the disk surface. All the specimens were subjected to thermal aging. The SBS and FS test was performed through a universal testing device. Two-way ANOVA, 1-way ANOVA, post hoc Tukey, and Tamhane tests were used for statistical analysis. (α=.05) RESULTS: The highest SBS values were observed at a layer height of 0.1 mm. The infill pattern had a significant effect on FS at all layer heights (0.1 mm P=.016, 0.2 mm P=.010, 0.3 mm P=.010). While the highest FS values at a 0.1-mm layer height were observed in the concentric pattern, no significant difference was identified between the L45 and L30 groups (P=.186). CONCLUSIONS: Lower layer heights strongly influenced the Ra, SBS and FS, with the highest SBS achieved with a layer height of 0.1 mm. To improve the mechanical properties of PEEK, the process parameters for additive manufacturing should be optimized.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Polyethylene GlycolsKetonesDental BondingDental MaterialsBenzophenonesPolymersSurface PropertiesMaterials TestingComposite ResinsShear StrengthDental Stress AnalysisFlexural StrengthIn Vitro TechniquesHumans

Substanzen

BenzophenonespolyetheretherketonePolyethylene GlycolsKetonesPolymersComposite ResinsDental Materials

Autor:innen und Institutionen

  • Associate Professor and Department Head, Department of Prosthodontics, Biruni University, Faculty of Dentistry, İstanbul, Turkey; and Guest Researcher, ADMiRE Research Center, Carinthia University of Applied Sciences, V…
  • Senior Researcher, ADMiRE Research Center, Carinthia University of Applied Sciences, Villach, Austria.
  • Associate Professor, ADMiRE Research Center, Carinthia University of Applied Sciences, Villach, Austria. Electronic address: s.spintzyk@fh-kaernten.at.
  • Doctoral student, Department of Prosthodontics, Biruni University, Faculty of Dentistry, İstanbul, Turkey.

Förderung

  • Evonik Industries

Zitieren

APA

Diken Türksayar, A. A., Schulnig, S., Spintzyk, S., & Yeşil Kurt, İ. B. (2025). Investigating the influence of infill pattern and layer height on the mechanical and bonding behavior of additively manufactured PEEK for dental applications. The Journal of Prosthetic Dentistry. https://doi.org/10.1016/j.prosdent.2025.03.010

Vancouver

Diken Türksayar AA, Schulnig S, Spintzyk S, Yeşil Kurt İB. Investigating the influence of infill pattern and layer height on the mechanical and bonding behavior of additively manufactured PEEK for dental applications. The Journal of Prosthetic Dentistry. 2025. doi:10.1016/j.prosdent.2025.03.010

BibTeX
@article{DikenTrksayar2025,
  author = {Diken Türksayar, Almira Ada and Schulnig, Sandra and Spintzyk, Sebastian and Yeşil Kurt, İrem Beril},
  title = {Investigating the influence of infill pattern and layer height on the mechanical and bonding behavior of additively manufactured PEEK for dental applications},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2025},
  doi = {10.1016/j.prosdent.2025.03.010}
}
Kostenlos starten →