EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Bond strength of recently introduced computer-aided design and computer-aided manufacturing resin-based crown materials to polyetheretherketone and titanium

Ahmet Serkan Küçükekenci, Mustafa Borga Dönmez, Doğu Ömür Dede, Gülce Çakmak, Burak Yilmaz

The Journal of Prosthetic Dentistry · 2024-11 · 132 (5) · 1066.e1-1066.e8

DOI: 10.1016/j.prosdent.2024.07.019 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2024-11. Verfasst von Ahmet Serkan Küçükekenci und 4 weiteren Autor:innen. Beteiligte Einrichtung: Associate Professor, Department of Prosthodontics, Faculty of Dentistry, Ordu University, Ordu, Turkey. Hauptthemen laut MEDLINE: Benzophenones, Polyethylene Glycols, Computer-Aided Design, Titanium. Die Arbeit wurde bisher 16-mal zitiert (Crossref) und nennt 34 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: Several additively and subtractively manufactured resin-based materials indicated for interim and definitive fixed dental prostheses have been launched. However, knowledge of the bond strength of these materials to different implant abutment materials is limited. PURPOSE: The purpose of this in vitro study was to evaluate the shear bond strength (SBS) of additively and subtractively manufactured resin-based materials to different implant abutment materials. MATERIAL AND METHODS: One hundred and ten disk-shaped specimens (Ø3×3 mm) were fabricated either additively from 2 resins indicated for definitive use (Crowntec; AM_CT and VarseoSmile Crown Plus; AM_VS) and 1 resin indicated for interim use (FREEPRINT temp; AM_FP) or subtractively from a nanographene-reinforced polymethyl methacrylate (G-CAM; SM_GC) and a high-impact polymer composite (breCAM.HIPC; SM_BC). After allocating 2 specimens from each group for scanning electron microscope evaluation, the specimens were divided according to the abutment material (CopraPeek; polyetheretherketone, PEEK and Dentium Superline Pre-Milled Abutment; titanium, Ti) (n=10). All specimens were airborne-particle abraded with 50-µm aluminum oxide. After applying a resin primer (Visio.link) to PEEK and an adhesive primer (Clearfil Ceramic Primer Plus) to Ti specimens, a self-adhesive resin cement (PANAVIA SA Cement Universal) was used for cementation. All specimens were stored in distilled water (24 hours, 37 °C), and a universal testing device was used for the SBS test. SBS data were analyzed with 2-way analysis of variance and Tukey honestly significant difference tests, while the chi-squared test was used to evaluate the difference among the abutment-resin pairs in terms of failure modes (α=.05). RESULTS: The interaction between the material type and the abutment type and the main factor of material type affected the SBS (P

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

BenzophenonesPolyethylene GlycolsComputer-Aided DesignTitaniumKetonesPolymersCrownsDental BondingMaterials TestingDental AbutmentsDental Stress AnalysisDental MaterialsShear StrengthHumansIn Vitro TechniquesPolymethyl MethacrylateComposite ResinsDental Implant-Abutment DesignMicroscopy, Electron, Scanning

Substanzen

polyetheretherketoneBenzophenonesPolyethylene GlycolsTitaniumKetonesPolymersDental MaterialsPolymethyl MethacrylateComposite Resins

Autor:innen und Institutionen

  • Associate Professor, Department of Prosthodontics, Faculty of Dentistry, Ordu University, Ordu, Turkey.
  • Associate Professor, Department of Prosthodontics, Faculty of Dentistry, Biruni University, Istanbul, Turkey; and ITI Scholar, Department of Reconstructive Dentistry and Gerodontology, School of Dental Medicine, Univers…
  • Professor, Department of Prosthodontics, Faculty of Dentistry, Ordu University, Ordu, Turkey.
  • Senior Research Associate, Department of Reconstructive Dentistry and Gerodontology, School of Dental Medicine, University of Bern, Bern, Switzerland.
  • Associate Professor, Department of Reconstructive Dentistry and Gerodontology, School of Dental Medicine, University of Bern, Bern, Switzerland; Associate Professor, Department of Restorative, Preventive and Pediatric D…

Zitieren

APA

Küçükekenci, A. S., Dönmez, M. B., Dede, D. Ö., Çakmak, G., & Yilmaz, B. (2024). Bond strength of recently introduced computer-aided design and computer-aided manufacturing resin-based crown materials to polyetheretherketone and titanium. The Journal of Prosthetic Dentistry, 132(5), 1066.e1-1066.e8. https://doi.org/10.1016/j.prosdent.2024.07.019

Vancouver

Küçükekenci AS, Dönmez MB, Dede DÖ, Çakmak G, Yilmaz B. Bond strength of recently introduced computer-aided design and computer-aided manufacturing resin-based crown materials to polyetheretherketone and titanium. The Journal of Prosthetic Dentistry. 2024;132(5):1066.e1-1066.e8. doi:10.1016/j.prosdent.2024.07.019

BibTeX
@article{Kkekenci2024,
  author = {Küçükekenci, Ahmet Serkan and Dönmez, Mustafa Borga and Dede, Doğu Ömür and Çakmak, Gülce and Yilmaz, Burak},
  title = {Bond strength of recently introduced computer-aided design and computer-aided manufacturing resin-based crown materials to polyetheretherketone and titanium},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2024},
  volume = {132},
  number = {5},
  pages = {1066.e1--1066.e8},
  doi = {10.1016/j.prosdent.2024.07.019}
}
Kostenlos starten →