Comparative analysis of flexural strength of 3D printed and milled 4Y-TZP and 3Y-TZP zirconia
The Journal of Prosthetic Dentistry · 2024-03 · 131 (3) · 529.e1-529.e9
DOI: 10.1016/j.prosdent.2023.12.020 ↗Kurz gefasst
Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2024-03. Verfasst von Kyu-Young Kyung und 6 weiteren Autor:innen. Beteiligte Einrichtung: PhD Candidate, Department of Prosthodontics & Dental Research Institute, School of Dentistry, Seoul National University, Seoul, Republic of Republic …. Hauptthemen laut MEDLINE: Flexural Strength, Printing, Three-Dimensional, Yttrium, Zirconium. Die Arbeit wurde bisher 26-mal zitiert (Crossref) und nennt 37 Literaturangaben. Gefördert von: Ministry of Health and Welfare, Ministry of Trade, Industry and Energy, Ministry of Food and Drug Safety.
Abstract (Originalsprache)
STATEMENT OF PROBLEM: The mechanical properties of 3 dimensionally (3D) printed zirconia have been reported to be comparable with those of milled zirconia, except for the flexural strength. However, most previous studies tested 3 mol% yttria-stabilized tetragonal zirconia polycrystal (3Y-TZP), making it necessary to study 3D printed zirconia with 4 mol% yttria content (4Y-TZP). PURPOSE: The purpose of this in vitro study was to compare the flexural strength of 3D printed 4Y-TZP with 3Y-TZP materials and milled 4Y-TZP. MATERIAL AND METHODS: A total of 80 disk specimens (Ø15×1.5 mm) were fabricated and divided into 4 groups (n=20) using the fabrication method and yttria content: milled 3Y-TZP (Katana HT; Kuraray Noritake), 3D printed 3Y-TZP (TZ-3Y-E; Tosoh), milled 4Y-TZP (Katana STML; Kuraray Noritake), and 3D printed 4Y-TZP (3DMAT; Genoss). The biaxial flexural strength was determined with a piston-on-3-ball test (n=15). The flexural strength of each specimen was measured, and the Weibull modulus (m) and characteristic strength (σ0) were estimated from the fracture load distribution. Two intact and fractured specimens were examined with scanning electron microscopy (SEM). The crystalline phase of the specimens in each group was identified through X-ray diffraction (XRD) analysis (n=5). A 1-way ANOVA was used to compare the flexural strength among different groups. Subsequently, pairwise comparisons were conducted with the Tukey post hoc method (α=.05). RESULTS: The flexural strength of 3D printed 4Y-TZP was significantly higher than that of milled 4Y-TZP (P
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Substanzen
Autor:innen und Institutionen
- PhD Candidate, Department of Prosthodontics & Dental Research Institute, School of Dentistry, Seoul National University, Seoul, Republic of Republic of Korea.
- Associate Professor, Department of Prosthodontics & Dental Research Institute, School of Dentistry, Seoul National University, Seoul, Republic of Korea. Electronic address: jimarn@gmail.com.
- Professor, Department of Prosthodontics & Dental Research Institute, School of Dentistry, Seoul National University, Seoul, Republic of Korea.
- Professor, Department of Dental Biomaterials Science & Dental Research Institute, School of Dentistry, Seoul National University, Seoul, Republic of Korea.
- Assistant Professor, Department of Prosthodontics & Dental Research Institute, School of Dentistry, Seoul National University, Seoul, Republic of Korea.
Förderung
- Ministry of Health and Welfare
- Ministry of Trade, Industry and Energy
- Ministry of Food and Drug Safety
- Korea Medical Device Development Fund
- Ministry of Science, ICT and Future Planning
Zitieren
APA
Kyung, K. Y., Park, J. M., Heo, S. J., Koak, J. Y., Kim, S. K., Ahn, J. S., & Yi, Y. (2024). Comparative analysis of flexural strength of 3D printed and milled 4Y-TZP and 3Y-TZP zirconia. The Journal of Prosthetic Dentistry, 131(3), 529.e1-529.e9. https://doi.org/10.1016/j.prosdent.2023.12.020
Vancouver
Kyung KY, Park JM, Heo SJ, Koak JY, Kim SK, Ahn JS, et al. Comparative analysis of flexural strength of 3D printed and milled 4Y-TZP and 3Y-TZP zirconia. The Journal of Prosthetic Dentistry. 2024;131(3):529.e1-529.e9. doi:10.1016/j.prosdent.2023.12.020
BibTeX
@article{Kyung2024,
author = {Kyung, Kyu-Young and Park, Ji-Man and Heo, Seong-Joo and Koak, Jai-Young and Kim, Seong-Kyun and Ahn, Jin-Soo and Yi, Yuseung},
title = {Comparative analysis of flexural strength of 3D printed and milled 4Y-TZP and 3Y-TZP zirconia},
journal = {The Journal of Prosthetic Dentistry},
year = {2024},
volume = {131},
number = {3},
pages = {529.e1--529.e9},
doi = {10.1016/j.prosdent.2023.12.020}
}
EUVIMED