EUVIMEDEUVIMED entdecken
Crossref

Evaluation of physicomechanical properties of milled versus 3D-printed denture base resins: A comparative in vitro study

Marwa M El Samahy, Ahmed M Abdelhamid, Sonia M El Shabrawy, Kenda I Hanno

The Journal of Prosthetic Dentistry · 2023-05 · 129 (5) · 797.e1-797.e7

DOI: 10.1016/j.prosdent.2023.03.017 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2023-05. Verfasst von Marwa M El Samahy und 3 weiteren Autor:innen. Beteiligte Einrichtung: Resident, Department of Prosthodontics, Faculty of Dentistry, University of Alexandria, Alexandria, Egypt. Hauptthemen laut MEDLINE: Denture Bases, Flexural Strength. Die Arbeit wurde bisher 33-mal zitiert (Crossref) und nennt 48 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: Studies comparing the physicomechanical characteristics of denture base resins manufactured by computer-aided design and computer-aided manufacturing (CAD-CAM) milling and 3-dimensional (3D) printing are sparse, resulting in challenges when choosing a fabrication method for complete dentures. PURPOSE: The purpose of this in vitro study was to evaluate and compare the impact strength, flexural strength, and the surface roughness of denture base resins manufactured by CAD-CAM milling and 3D printing before and after thermocycling and polishing. MATERIAL AND METHODS: Evaluation of the physicomechanical properties (n=35) was completed before and after 500 thermocycles. Impact strength (n=14) was measured with a Charpy impact tester and flexural strength (n=14) with the 3-point bend test. Surface roughness (Ra) was evaluated (n=7) with a profilometer before and after thermocycling and polishing and by viewing the surface topography before and after polishing using a scanning electron microscope at ×2000. The Mann-Whitney U test and Wilcoxon sign rank test were used for statistical analysis (α=.05). RESULTS: Milled specimens showed statistically significantly higher impact strength before thermocycling and statistically significantly higher flexural strength before and after thermocycling (P=.004) compared with 3D-printed specimens. The Ra values for the milled group were significantly lower than for the 3D-printed group both before and after thermocycling (P=.006) and after polishing (P=.027). Thermocycling resulted in a statistically significant difference in flexural strength (P=.018) in both groups and in surface roughness in the milled group (P=.048); but no significant effect was found on impact strength (P>.05). Ra values for the 3D-printed group decreased after polishing (P=.048). CONCLUSIONS: Milled specimens had higher flexural and impact strength and lower surface roughness values than 3D-printed specimens. Polishing significantly reduced the surface roughness in 3D-printed specimens but had no significant effect on milled specimens.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Denture BasesFlexural StrengthMaterials TestingSurface PropertiesComputer-Aided DesignPrinting, Three-Dimensional

Autor:innen und Institutionen

  • Resident, Department of Prosthodontics, Faculty of Dentistry, University of Alexandria, Alexandria, Egypt.
  • Professor, Department of Prosthodontics, Faculty of Dentistry, University of Alexandria, Alexandria, Egypt.
  • Professor, Department of Dental Biomaterials, Faculty of Dentistry, University of Alexandria, Alexandria, Egypt.
  • Lecturer, Department of Prosthodontics, Faculty of Dentistry, University of Alexandria, Alexandria, Egypt. Electronic address: kendahanno@gmail.com.

Zitieren

APA

El Samahy, M. M., Abdelhamid, A. M., El Shabrawy, S. M., & Hanno, K. I. (2023). Evaluation of physicomechanical properties of milled versus 3D-printed denture base resins: A comparative in vitro study. The Journal of Prosthetic Dentistry, 129(5), 797.e1-797.e7. https://doi.org/10.1016/j.prosdent.2023.03.017

Vancouver

El Samahy MM, Abdelhamid AM, El Shabrawy SM, Hanno KI. Evaluation of physicomechanical properties of milled versus 3D-printed denture base resins: A comparative in vitro study. The Journal of Prosthetic Dentistry. 2023;129(5):797.e1-797.e7. doi:10.1016/j.prosdent.2023.03.017

BibTeX
@article{ElSamahy2023,
  author = {El Samahy, Marwa M and Abdelhamid, Ahmed M and El Shabrawy, Sonia M and Hanno, Kenda I},
  title = {Evaluation of physicomechanical properties of milled versus 3D-printed denture base resins: A comparative in vitro study},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2023},
  volume = {129},
  number = {5},
  pages = {797.e1--797.e7},
  doi = {10.1016/j.prosdent.2023.03.017}
}
Kostenlos starten →