EUVIMEDEUVIMED entdecken
VergleichsstudieOpen Access · CC BY 4.0

Performance parity in cartilage repair: SPMK-g-PEEK versus cartilage–cartilage interfaces

Robert J Elkington, Gregory M Pryce, David Keeling, Richard M Hall, Andrew R Beadling, Hemant Pandit, Michael G Bryant

Journal of the Mechanical Behavior of Biomedical Materials · 2025-07 · 167 · 106964

DOI: 10.1016/j.jmbbm.2025.106964 ↗

Kurz gefasst

Vergleichsstudie in der Zeitschrift Journal of the Mechanical Behavior of Biomedical Materials, 2025-07. Verfasst von Robert J Elkington und 6 weiteren Autor:innen. Beteiligte Einrichtung: Institute of Functional Surfaces, Mechanical Engineering, University of Leeds, Leeds, LS2 9JT, Yorkshire, UK. Electronic address: mnrje@leeds.ac.uk. Hauptthemen laut MEDLINE: Cartilage, Articular, Polyethylene Glycols, Ketones, Methacrylates. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 99 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Engineering and Physical Sciences Research Council, UK Research and Innovation, University of Leeds.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Effective fluid exudation and rehydration are essential for the low-friction function of healthy articular cartilage, facilitating interstitial fluid pressurisation, solute transport, and aqueous lubrication. However, current metallic biomaterials used in focal cartilage repair or hemiarthroplasty compromise this fluid-pressure dependent load support, leading to the erosion of the interfacing cartilage. This study investigates bioinspired hydrophilic 3-sulfopropyl methacrylate potassium salt (SPMK) polymer grafted onto a PEEK substrate (SPMK-g-PEEK) as a potential solution. SPMK-g-PEEK aims to mimic the natural tribology of cartilage by providing an aqueous low friction interface and polyelectrolyte-enhanced tribological rehydration (PETR), supporting fluid recovery and interstitial fluid pressurisation during cartilage sliding. We compare the tribological characteristics of physiological cartilage-cartilage interfaces, which rely on osmotic swelling and hydrodynamic tribological rehydration, with PETR enabled by SPMK-g-PEEK interfaces. This study introduces a bespoke Fuzzy-PI controlled biotribometer. Employing a dual-phase testing method, static compression followed by sliding, allows simultaneous measurement of friction and cartilage strain recovery, indicative of interstitial fluid recovery following compressive exudation. Cartilage condyle, unfunctionalised PEEK, and SPMK-g-PEEK surfaces were investigated against flat cartilage plugs, which provide no hydrodynamic entrainment zone for tribological rehydration, and convex cartilage plugs, which create a convergent hydrodynamic zone for tribological rehydration. Matched cartilage-cartilage contacts exhibited low friction coefficients of ∼ 0.04 and strain recovery of up to ∼ 14% during the sliding phase. SPMK-g-PEEK surfaces sliding against convex cartilage plugs demonstrated similar strain recovery of ∼ 13% and reduced friction coefficients of ∼ 0.01, due to the combined effects of PETR and hydrodynamic tribological rehydration. In contrast, unfunctionalised PEEK surfaces, similar to current hard biomaterials employed in cartilage resurfacing, showed significantly higher friction and inhibited rehydration. SPMK-g-PEEK effectively mimics the physiological rehydration of connatural articular cartilage surfaces, highlighting its potential as a biomimetic material for cartilage resurfacing.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Cartilage, ArticularPolyethylene GlycolsKetonesMethacrylatesBiocompatible MaterialsBenzophenonesAnimalsMaterials TestingPolymersFriction

Stichwörter der Autor:innen

Aqueous lubricationBioTribologyBiphasic lubricationCartilagePolymer brushesTribological rehydration

Substanzen

BenzophenonespolyetheretherketonePolyethylene GlycolsKetonesPolymersMethacrylatesBiocompatible Materials

Autor:innen und Institutionen

  • Institute of Functional Surfaces, Mechanical Engineering, University of Leeds, Leeds, LS2 9JT, Yorkshire, UK. Electronic address: mnrje@leeds.ac.uk.
  • Institute of Functional Surfaces, Mechanical Engineering, University of Leeds, Leeds, LS2 9JT, Yorkshire, UK.
  • Key Engineering Solutions Limited, Leeds, LS2 3AA, Yorkshire, UK.
  • School of Engineering, College of Engineering and Physical Sciences, University of Birmingham, Birmingham, B15 2TT, West Midlands, UK.
  • Leeds Institute of Rheumatic and Musculoskeletal Medicine, Chapel Allerton Hospital, Chapeltown Road, Leeds, LS7 4SA, Yorkshire, UK.
  • School of Engineering, College of Engineering and Physical Sciences, University of Birmingham, Birmingham, B15 2TT, West Midlands, UK. Electronic address: m.g.bryant@bham.ac.uk.

Förderung

  • Engineering and Physical Sciences Research Council
  • UK Research and Innovation
  • University of Leeds

Zitieren

APA

Elkington, R. J., Pryce, G. M., Keeling, D., Hall, R. M., Beadling, A. R., Pandit, H., & Bryant, M. G. (2025). Performance parity in cartilage repair: SPMK-g-PEEK versus cartilage–cartilage interfaces. Journal of the Mechanical Behavior of Biomedical Materials, 167, 106964. https://doi.org/10.1016/j.jmbbm.2025.106964

Vancouver

Elkington RJ, Pryce GM, Keeling D, Hall RM, Beadling AR, Pandit H, et al. Performance parity in cartilage repair: SPMK-g-PEEK versus cartilage–cartilage interfaces. Journal of the Mechanical Behavior of Biomedical Materials. 2025;167:106964. doi:10.1016/j.jmbbm.2025.106964

BibTeX
@article{Elkington2025,
  author = {Elkington, Robert J and Pryce, Gregory M and Keeling, David and Hall, Richard M and Beadling, Andrew R and Pandit, Hemant and Bryant, Michael G},
  title = {Performance parity in cartilage repair: SPMK-g-PEEK versus cartilage–cartilage interfaces},
  journal = {Journal of the Mechanical Behavior of Biomedical Materials},
  year = {2025},
  volume = {167},
  pages = {106964},
  doi = {10.1016/j.jmbbm.2025.106964}
}
Kostenlos starten →