EUVIMEDEUVIMED entdecken
Crossref

Fracture toughness and subcritical crack growth analysis of high-translucent zirconia prepared by stereolithography-based additive manufacturing

Li Wang, Kang Wang, Zongdong Hao, Rui Dou, Fangyong Zhu, Yufeng Gao

Journal of the Mechanical Behavior of Biomedical Materials · 2025-04 · 164 · 106917

DOI: 10.1016/j.jmbbm.2025.106917 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of the Mechanical Behavior of Biomedical Materials, 2025-04. Verfasst von Li Wang und 5 weiteren Autor:innen. Beteiligte Einrichtung: Jiangsu Key Laboratory of Advanced Food Manufacturing Equipment and Technology, School of Mechanical Engineering, Jiangnan University, Wuxi, 214122, …. Hauptthemen laut MEDLINE: Zirconium, Mechanical Phenomena, Stereolithography. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 46 Literaturangaben. Gefördert von: National Key Research and Development Program of China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The objective was to study the subcritical crack growth phenomena and determine the fracture toughness of two yttria-partially-stabilized zirconia ceramics. One of the two materials evaluated was a commercially available 5 mol% yttria partially stabilized zirconia (5Y-PSZ), and the other was an experimental partially stabilized zirconia made from a mixture of 3 mol% and 8 mol% yttria stabilized zirconia powder (3Y+8Y-PSZ), with the final samples prepared by the Stereolithography (SLA) process. The samples in water were tested by three-point bending experiments at different stress rates to obtain Weibull and SCG parameters. The results show that 3Y+8Y-PSZ has higher Weibull modulus(m = 11.54) and characteristic strength(σ0 = 812.27 MPa) compared to 5Y-PSZ (m = 8.57, σ0 = 647.25 MPa). SCG parameters n obtained for 5Y-PSZ and 3Y+8Y-PSZ tested in water were 26.03, 37.94, respectively. The strength of 5Y-PSZ and 3Y+8Y-PSZ (Pf = 5%) was reduced by 56.49%, 45.30% after 10 years of simulated use. Regarding the fracture toughness of both materials, 3Y+8Y-PSZ had higher values regardless of the method used to determine it. However, the fitting correction factor of the Vickers indentation method was not applicable to either 5Y-PSZ or 3Y+8Y-PSZ. Determining the SCG parameters of two materials and predicting their lifetimes using constant stress rate testing is an effective way to evaluate materials.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

ZirconiumMechanical PhenomenaStereolithographyMaterials TestingYttriumStress, Mechanical

Stichwörter der Autor:innen

Fracture toughnessStereolithographySubcritical crack growthYttrium partially stabilized zirconia

Substanzen

Zirconiumzirconium oxideYttrium

Autor:innen und Institutionen

  • Jiangsu Key Laboratory of Advanced Food Manufacturing Equipment and Technology, School of Mechanical Engineering, Jiangnan University, Wuxi, 214122, Jiangsu, China; School of Mechanical Engineering, Jiangnan University,…
  • Department of Stomatology, Affiliated Hospital of Jiangnan University, Wuxi, 214122, Jiangsu, China; School of Food Science and Technology, Jiangnan University, Wuxi, 214122, Jiangsu, China. Electronic address: 4645056@…
  • Wuxi People's Hospital, Wuxi, 214000, Jiangsu, China.

Förderung

  • National Key Research and Development Program of China

Zitieren

APA

Wang, L., Wang, K., Hao, Z., Dou, R., Zhu, F., & Gao, Y. (2025). Fracture toughness and subcritical crack growth analysis of high-translucent zirconia prepared by stereolithography-based additive manufacturing. Journal of the Mechanical Behavior of Biomedical Materials, 164, 106917. https://doi.org/10.1016/j.jmbbm.2025.106917

Vancouver

Wang L, Wang K, Hao Z, Dou R, Zhu F, Gao Y. Fracture toughness and subcritical crack growth analysis of high-translucent zirconia prepared by stereolithography-based additive manufacturing. Journal of the Mechanical Behavior of Biomedical Materials. 2025;164:106917. doi:10.1016/j.jmbbm.2025.106917

BibTeX
@article{Wang2025,
  author = {Wang, Li and Wang, Kang and Hao, Zongdong and Dou, Rui and Zhu, Fangyong and Gao, Yufeng},
  title = {Fracture toughness and subcritical crack growth analysis of high-translucent zirconia prepared by stereolithography-based additive manufacturing},
  journal = {Journal of the Mechanical Behavior of Biomedical Materials},
  year = {2025},
  volume = {164},
  pages = {106917},
  doi = {10.1016/j.jmbbm.2025.106917}
}
Kostenlos starten →