Evaluation of a digital method for determination of the occlusal plane by using facial landmarks and symmetry analysis against conventional complete dentures: a pilot study
Digital Dentistry Journal · 2026-12 · 4 (1) · 100134
DOI: 10.1016/j.ddj.2026.100134 ↗Kurz gefasst
Fachartikel in der Zeitschrift Digital Dentistry Journal, 2026-12. Verfasst von Shenghan Gao und 5 weiteren Autor:innen. Die Arbeit nennt 55 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Beijing Natural Science Foundation.
Abstract (Originalsprache)
Purpose
To evaluate the agreement between a digitally determined occlusal plane based on a symmetry reference plane (SRP) combined with the ala-tragus line and the occlusal planes of clinically accepted complete dentures. Materials and Methods Twenty edentulous participants were recruited. Facial scans and digital prostheses were acquired. Virtual patients (VPs) were constructed by aligning the scans. The SRPs of each VP were generated using weighted Procrustes analysis (WPA) based on 32 facial landmarks. Nine candidate occlusal planes were established for each VP by orienting the plane perpendicular to the SRP frontally and parallel to each of the nine ala-tragus line combinations derived from three ala points (superior, middle, inferior) (A1, A2, A3) and three tragus points (superior, middle, inferior) (T1, T2, T3) laterally. The occlusal plane of the digital prostheses served as the reference occlusal plane. Angle differences between each candidate plane and the reference plane were calculated.
Results
Among the nine candidate occlusal planes, the occlusal plane defined by the middle point of the ala and the superior point of the tragus (A2-T1) showed the smallest median angle difference to the reference plane (2.69°, 2.33°/5.22°). Multiple ala-tragus combinations showed comparable angle differences, with no statistically significant differences among them. The largest difference was observed in the A1-T3 group (11.40°, 6.77°/13.29°), which was significantly greater than the differences observed in the A1-T1, A2-T1, A2-T2, A3-T2, and A3-T3 groups.
Conclusions
Within the limitations of this single-center pilot study with 20 participants, the digital method for determining the occlusal-plane orientation indicated preliminary agreement with clinically accepted denture planes in a small, selected sample. Clinical significance This study proposes a digital method for determining the occlusal plane orientation, which may reduce subjective dependence in complete denture workflows. However, further studies are needed to evaluate fabrication and adjustment of the occlusal rim based on the digitally determined occlusal plane.
Förderung
- Beijing Natural Science Foundation
Zitieren
APA
Gao, S., Guo, D., Zhu, Y., Zhao, Y., Wang, Y., & Pan, S. (2026). Evaluation of a digital method for determination of the occlusal plane by using facial landmarks and symmetry analysis against conventional complete dentures: a pilot study. Digital Dentistry Journal, 4(1), 100134. https://doi.org/10.1016/j.ddj.2026.100134
Vancouver
Gao S, Guo D, Zhu Y, Zhao Y, Wang Y, Pan S. Evaluation of a digital method for determination of the occlusal plane by using facial landmarks and symmetry analysis against conventional complete dentures: a pilot study. Digital Dentistry Journal. 2026;4(1):100134. doi:10.1016/j.ddj.2026.100134
BibTeX
@article{Gao2026,
author = {Gao, Shenghan and Guo, Danni and Zhu, Yujia and Zhao, Yijiao and Wang, Yong and Pan, Shaoxia},
title = {Evaluation of a digital method for determination of the occlusal plane by using facial landmarks and symmetry analysis against conventional complete dentures: a pilot study},
journal = {Digital Dentistry Journal},
year = {2026},
volume = {4},
number = {1},
pages = {100134},
doi = {10.1016/j.ddj.2026.100134}
}
EUVIMED