EUVIMEDEUVIMED entdecken
Crossref

Optimize the pore size-pore distribution-pore geometry-porosity of 3D-printed porous tantalum to obtain optimal critical bone defect repair capability

Xueying Wang, Dachen Zhang, Haitao Peng, Jingzhou Yang, Yan Li, Jianxia Xu

Biomaterials Advances · 2023-11 · 154 · 213638

DOI: 10.1016/j.bioadv.2023.213638 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Biomaterials Advances, 2023-11. Verfasst von Xueying Wang und 5 weiteren Autor:innen. Beteiligte Einrichtung: Biomaterials Laboratory of the Medical Device Inspection Institute, National Institutes for Food and Drug Control, Beijing, China; School of Material…. Hauptthemen laut MEDLINE: Tantalum, Osteogenesis. Die Arbeit wurde bisher 41-mal zitiert (Crossref) und nennt 45 Literaturangaben. Gefördert von: National Key Research and Development Program of China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The treatment and reconstruction of large or critical size bone defects is a challenging clinical problem. Additive manufacturing breaks the technical difficulties of preparing complex conformation and anatomically matched personalized porous tantalum implants, but the ideal pore structure for 3D-printed porous tantalum in critical bone defect repair applications remains unclear. Guiding appropriate bone tissue regeneration by regulating proper pore size-pore distribution-pore geometry-porosity is a challenge for its fabrication and application. We fabricated porous tantalum (PTa) scaffolds with six different combinations of pore structures using powder bed laser melting (L-PBF) technology. In vitro biological experiments were conducted to systematically investigate the effects of pore structure characteristics on osteoblast behaviors, showing that the bionic trabecular structure with both large and small poress facilitated cell permeation, proliferation and differentiation compared to the cubic structure with uniform pore sizes. The osteogenesis of PTa with different porosity of trabecular structures was further investigated by a rabbit condyle critical bone defect model. Synthetically, T70% up-regulated the expression of osteogenesis-related genes (ALP, COLI, OCN, RUNX-2) and showed the highest bone ingrowth area and bone contact rate in vivo after 16 weeks, with the best potential for critical bone defect repair. Our results suggested that the bionic trabecular structure with a pore size distribution of 200-1200 μm, an average pore size of 700 μm, and a porosity of 70 % is the best choice for repairing critical bone defects, which is expected to guide the clinical application of clinical 3D-printed PTa scaffolds.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

TantalumOsteogenesisAnimalsRabbitsPorosityBone and BonesPrinting, Three-Dimensional

Stichwörter der Autor:innen

Additive manufacturingBone defectOsseointegrationPore sizePorosityPorous tantalum

Substanzen

Tantalum

Autor:innen und Institutionen

  • Biomaterials Laboratory of the Medical Device Inspection Institute, National Institutes for Food and Drug Control, Beijing, China; School of Material Science and Engineering, Beihang University, Beijing, China.
  • Shenzhen Dazhou Medical Technology Co., Ltd., Shenzhen, Guangdong, China.
  • State Key Laboratory of Biotherapy and Cancer Center, West China Hospital of Sichuan University, Chengdu, Sichuan, China.
  • Shenzhen Dazhou Medical Technology Co., Ltd., Shenzhen, Guangdong, China; School of Mechanical and Automobile Engineering, Qingdao University of Technology, Qingdao, Shandong, China. Electronic address: yangjz@qut.edu.c…
  • School of Material Science and Engineering, Beihang University, Beijing, China. Electronic address: liyan@buaa.edu.cn.
  • Biomaterials Laboratory of the Medical Device Inspection Institute, National Institutes for Food and Drug Control, Beijing, China. Electronic address: xujianxia@nifdc.org.cn.

Förderung

  • National Key Research and Development Program of China

Zitieren

APA

Wang, X., Zhang, D., Peng, H., Yang, J., Li, Y., & Xu, J. (2023). Optimize the pore size-pore distribution-pore geometry-porosity of 3D-printed porous tantalum to obtain optimal critical bone defect repair capability. Biomaterials Advances, 154, 213638. https://doi.org/10.1016/j.bioadv.2023.213638

Vancouver

Wang X, Zhang D, Peng H, Yang J, Li Y, Xu J. Optimize the pore size-pore distribution-pore geometry-porosity of 3D-printed porous tantalum to obtain optimal critical bone defect repair capability. Biomaterials Advances. 2023;154:213638. doi:10.1016/j.bioadv.2023.213638

BibTeX
@article{Wang2023,
  author = {Wang, Xueying and Zhang, Dachen and Peng, Haitao and Yang, Jingzhou and Li, Yan and Xu, Jianxia},
  title = {Optimize the pore size-pore distribution-pore geometry-porosity of 3D-printed porous tantalum to obtain optimal critical bone defect repair capability},
  journal = {Biomaterials Advances},
  year = {2023},
  volume = {154},
  pages = {213638},
  doi = {10.1016/j.bioadv.2023.213638}
}
Kostenlos starten →