EUVIMEDEUVIMED entdecken
Vergleichsstudie

Post-Cam Design Influences the Mechanics and Interface Micromotion of the Tibial Prosthesis Fixation in Posterior-Stabilized Total Knee Arthroplasty: Comparison Among Three Common Designs

Jianian Han, Weijie Zhang, Jing Zhang, Zhenxian Chen, Zhongmin Jin

The Journal of Arthroplasty · 2025

DOI: 10.1016/j.arth.2025.05.047 ↗

Kurz gefasst

Vergleichsstudie in der Zeitschrift The Journal of Arthroplasty, 2025. Verfasst von Jianian Han und 4 weiteren Autor:innen. Beteiligte Einrichtung: School of Mechanical Engineering, Chang'an University, Xi'an, Shaanxi, China. Hauptthemen laut MEDLINE: Arthroplasty, Replacement, Knee, Prosthesis Design, Knee Prosthesis, Tibia. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 45 Literaturangaben. Gefördert von: National Natural Science Foundation of China, Fundamental Research Funds for the Central Universities, Natural Science Foundation of Shaanxi Province.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

BACKGROUND: Posterior-stabilized prosthesis tibial postloading influences mechanical transfer and micromotion at the tibial prosthesis fixation interface, thereby increasing the risk of prosthesis loosening. However, the effect of different post-cam designs on tibial prosthesis fixation remains unclear. METHODS: In this paper, finite element models with and without posts were developed for three common posterior-stabilized prostheses with different post-cam designs (TKA A, B, and C) to investigate the effects of postloading on the von Mises stresses of the proximal tibia, shear stresses of the cement, axial displacement of the tibial tray, and micromotion of the fixation interface under the standing-up-sitting-down and stair descent activities, and to compare the differences in the initial stability of tibial prosthesis fixation under three different post-cam designs. RESULTS: Posterior-stabilized prosthesis postloading significantly increased shear stress of the cement and micromotion of the tibial prosthesis fixation interface at the moment of the maximum flexion angle during the standing-up-sitting-down and stair descent activities. Compared to the TKA A prosthesis with a higher post-cam contact position, the peak fixation interface micromotion of the TKA B prosthesis was reduced by 60.1 and 51.4%, the TKA C prosthesis was reduced by 44.6 and 53.5%, and the postloading interval was significantly smaller for the former. CONCLUSIONS: The post-cam design of the posterior-stabilized prosthesis should consider a lower post-cam contact position while avoiding square designs with small spacing between the post and the intercondylar groove of the femoral component and recommending a round post design.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Arthroplasty, Replacement, KneeProsthesis DesignKnee ProsthesisTibiaHumansFinite Element AnalysisBiomechanical PhenomenaStress, MechanicalKnee Joint

Stichwörter der Autor:innen

finite element analysispost-cam mechanismsposterior-stabilized prosthesisstress distributiontibial postloadingtotal knee arthroplasty

Autor:innen und Institutionen

  • School of Mechanical Engineering, Chang'an University, Xi'an, Shaanxi, China.
  • Department of Orthopaedics, Honghui Hospital, Xi'an Jiaotong University, Xi'an, Shaanxi, China.
  • State Key Laboratory for Manufacturing System Engineering, School of Mechanical Engineering, Xi'an Jiaotong University, Xi'an, Shaanxi, China; Institute of Medical and Biological Engineering, School of Mechanical Engine…

Förderung

  • National Natural Science Foundation of China
  • Fundamental Research Funds for the Central Universities
  • Natural Science Foundation of Shaanxi Province
  • Chang'an University

Zitieren

APA

Han, J., Zhang, W., Zhang, J., Chen, Z., & Jin, Z. (2025). Post-Cam Design Influences the Mechanics and Interface Micromotion of the Tibial Prosthesis Fixation in Posterior-Stabilized Total Knee Arthroplasty: Comparison Among Three Common Designs. The Journal of Arthroplasty. https://doi.org/10.1016/j.arth.2025.05.047

Vancouver

Han J, Zhang W, Zhang J, Chen Z, Jin Z. Post-Cam Design Influences the Mechanics and Interface Micromotion of the Tibial Prosthesis Fixation in Posterior-Stabilized Total Knee Arthroplasty: Comparison Among Three Common Designs. The Journal of Arthroplasty. 2025. doi:10.1016/j.arth.2025.05.047

BibTeX
@article{Han2025,
  author = {Han, Jianian and Zhang, Weijie and Zhang, Jing and Chen, Zhenxian and Jin, Zhongmin},
  title = {Post-Cam Design Influences the Mechanics and Interface Micromotion of the Tibial Prosthesis Fixation in Posterior-Stabilized Total Knee Arthroplasty: Comparison Among Three Common Designs},
  journal = {The Journal of Arthroplasty},
  year = {2025},
  doi = {10.1016/j.arth.2025.05.047}
}
Kostenlos starten →