EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Mechanical characterization of an incompressible, strain-hardening, transversely isotropic material

Qifeng Wang, Sheng Wang, Mahdi Ebrahimkhani, Thomas J Royston, Eric J Perreault, Kenneth R Shull

Acta Biomaterialia · 2026-01 · 209 · 440-451

DOI: 10.1016/j.actbio.2025.10.062 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Acta Biomaterialia, 2026-01. Verfasst von Qifeng Wang und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Materials Science and Engineering, Northwestern University, 2220 Campus Drive, Evanston, 60208, IL, USA. Hauptthemen laut MEDLINE: Stress, Mechanical, Materials Testing. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 50 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: NIAMS NIH HHS, Center for Hierarchical Materials Design, National Institute of Arthritis and Musculoskeletal and Skin Diseases.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

A strain energy approach for the characterization of strain-hardening, transversely isotropic materials was developed and validated through a combination of indentation and uniaxial extension experiments. These experiments were utilized because they can also be applied to directly measure the mechanical properties of many living tissues, including muscle. Model materials with transversely isotropic mechanical properties broadly representative of biological tissues were utilized in the experiments. These organogels were made from acrylic triblock copolymer solutions with an aligned cylindrical domain morphology. The strain energy function used here was proposed recently by Hegde et al., and is based on the three independent linear elastic constants for a transversely isotropic material, along with two additional strain-hardening parameters. These five parameters were determined for the model material by indentation with a blade indenter aligned both parallel and perpendicular to the unique axis of the gel, and by uniaxial extension of the material along the directions parallel and perpendicular to the unique axis. The effect on the indentation curves of an applied tensile pre-stress applied along the unique axis was also investigated. Finite element modeling was used to generate interpolated functions that allow the elastic constants, along with their uncertainty, to be obtained from the experimental data in a straightforward manner. These parameters were then used to predict the wave speeds in pre-stressed material that would be measured by shear wave elastography, a commonly used technique for non-invasively characterizing the mechanical properties of biological tissues.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Stress, MechanicalMaterials TestingFinite Element AnalysisHardnessAnisotropyTensile StrengthElasticityElastic Modulus

Stichwörter der Autor:innen

Finite element analysisIndentationShear wave elastographyStrain energyTransversely isotropic

Autor:innen und Institutionen

  • Department of Materials Science and Engineering, Northwestern University, 2220 Campus Drive, Evanston, 60208, IL, USA.
  • Department of Biomedical Engineering, Northwestern University, 2145 Sheridan Road, Evanston, 60208, IL, USA; Shirley Ryan AbilityLab, 355 E Erie Street, Chicago, 60611, IL, USA.
  • Richard and Loan Hill Department of Biomedical Engineering, University of Illinois Chicago, 851 South Morgan Street, Chicago, 60607, IL, USA.
  • Department of Biomedical Engineering, Northwestern University, 2145 Sheridan Road, Evanston, 60208, IL, USA; Shirley Ryan AbilityLab, 355 E Erie Street, Chicago, 60611, IL, USA; Department of Physical Medicine and Rehab…
  • Department of Materials Science and Engineering, Northwestern University, 2220 Campus Drive, Evanston, 60208, IL, USA. Electronic address: k-shull@northwestern.edu.

Förderung

  • NIAMS NIH HHS
  • Center for Hierarchical Materials Design
  • National Institute of Arthritis and Musculoskeletal and Skin Diseases
  • National Institutes of Health
  • Materials Research Science and Engineering Center, Northwestern University
  • U.S. Department of Commerce
  • National Institute of Standards and Technology
  • National Science Foundation

Zitieren

APA

Wang, Q., Wang, S., Ebrahimkhani, M., Royston, T. J., Perreault, E. J., & Shull, K. R. (2026). Mechanical characterization of an incompressible, strain-hardening, transversely isotropic material. Acta Biomaterialia, 209, 440-451. https://doi.org/10.1016/j.actbio.2025.10.062

Vancouver

Wang Q, Wang S, Ebrahimkhani M, Royston TJ, Perreault EJ, Shull KR. Mechanical characterization of an incompressible, strain-hardening, transversely isotropic material. Acta Biomaterialia. 2026;209:440-451. doi:10.1016/j.actbio.2025.10.062

BibTeX
@article{Wang2026,
  author = {Wang, Qifeng and Wang, Sheng and Ebrahimkhani, Mahdi and Royston, Thomas J and Perreault, Eric J and Shull, Kenneth R},
  title = {Mechanical characterization of an incompressible, strain-hardening, transversely isotropic material},
  journal = {Acta Biomaterialia},
  year = {2026},
  volume = {209},
  pages = {440--451},
  doi = {10.1016/j.actbio.2025.10.062}
}
Kostenlos starten →