Digital light 4D printing of bioresorbable shape memory elastomers for personalized biomedical implantation
Acta Biomaterialia · 2024-03 · 177 · 165-177
DOI: 10.1016/j.actbio.2024.02.009 ↗Kurz gefasst
Fachartikel in der Zeitschrift Acta Biomaterialia, 2024-03. Verfasst von Alireza Mahjoubnia und 8 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical and Aerospace Engineering, University of Missouri, Columbia, 65211, USA. Hauptthemen laut MEDLINE: Elastomers, Tissue Scaffolds. Die Arbeit wurde bisher 75-mal zitiert (Crossref) und nennt 55 Literaturangaben. Der Volltext ist frei in PubMed Central verfügbar. Gefördert von: NHLBI NIH HHS, NIBIB NIH HHS, NEI NIH HHS.
Abstract (Originalsprache)
Four-dimensional (4D) printing unlocks new potentials for personalized biomedical implantation, but still with hurdles of lacking suitable materials. Herein, we demonstrate a bioresorbable shape memory elastomer (SME) with high elasticity at both below and above its phase transition temperature (Ttrans). This SME can be digital light 3D printed by co-polymerizing glycerol dodecanoate acrylate prepolymer (pre-PGDA) with acrylic acid monomer to form crosslinked Poly(glycerol dodecanoate acrylate) (PGDA)-Polyacrylic acid (PAA), or PGDA-PAA network. The printed complex, free-standing 3D structures with high-resolution features exhibit shape programming properties at a physiological temperature. By tuning the pre-PGDA weight ratios between 55 wt% and 70 wt%, Ttrans varies between 39.2 and 47.2 ℃ while Young's moduli (E) range 40-170 MPa below Ttrans with fractural strain (εf) of 170 %-200 %. Above Ttrans, E drops to 1-1.82 MPa which is close to those of soft tissue. Strikingly, εf of 130-180 % is still maintained. In vitro biocompatibility test on the material shows > 90 % cell proliferation and great cell attachment. In vivo vascular grafting trials underline the geometrical and mechanical adaptability of these 4D printed constructs in regenerating the aorta tissue. Biodegradation of the implants shows the possibility of their full replacement by natural tissue over time. To highlight its potential for personalized medicine, a patient-specific left atrial appendage (LAA) occluder was printed and implanted endovascularly into an in vitro heart model. STATEMENT OF SIGNIFICANCE: 4D printed shape-memory elastomer (SME) implants particularly designed and manufactured for a patient are greatly sought-after in minimally invasive surgery (MIS). Traditional shape-memory polymers used in these implants often suffer from issues like unsuitable transition temperatures, poor biocompatibility, limited 3D design complexity, and low toughness, making them unsuitable for MIS. Our new SME, with an adjustable transition temperature and enhanced toughness, is both biocompatible and naturally degradable, particularly in cardiovascular contexts. This allows implants, like biomedical scaffolds, to be programmed at room temperature and then adapt to the body's physiological conditions post-implantation. Our studies, including in vivo vascular grafts and in vitro device implantation, highlight the SME's effectiveness in aortic tissue regeneration and its promising applications in MIS.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Department of Mechanical and Aerospace Engineering, University of Missouri, Columbia, 65211, USA.
- Department of Surgery, School of Medicine, University of Missouri, Columbia, 65211, USA.
- Vascular and Interventional Radiology, Department of Radiology, University of Minnesota, Minneapolis, 55455, USA.
- Department of Surgery, School of Medicine, University of Missouri, Columbia, 65211, USA; North Oconee High School, Bogart, GA 30622, USA.
- Department of Surgery, School of Medicine, University of Missouri, Columbia, 65211, USA. Electronic address: scqvd@missouri.edu.
- Department of Mechanical and Aerospace Engineering, University of Missouri, Columbia, 65211, USA. Electronic address: linjian@missouri.edu.
Förderung
- NHLBI NIH HHS
- NIBIB NIH HHS
- NEI NIH HHS
- Medtronic
- National Institutes of Health
Zitieren
APA
Mahjoubnia, A., Cai, D., Wu, Y., King, S. D., Torkian, P., Chen, A. C., Talaie, R., Chen, S. Y., & Lin, J. (2024). Digital light 4D printing of bioresorbable shape memory elastomers for personalized biomedical implantation. Acta Biomaterialia, 177, 165-177. https://doi.org/10.1016/j.actbio.2024.02.009
Vancouver
Mahjoubnia A, Cai D, Wu Y, King SD, Torkian P, Chen AC, et al. Digital light 4D printing of bioresorbable shape memory elastomers for personalized biomedical implantation. Acta Biomaterialia. 2024;177:165-177. doi:10.1016/j.actbio.2024.02.009
BibTeX
@article{Mahjoubnia2024,
author = {Mahjoubnia, Alireza and Cai, Dunpeng and Wu, Yuchao and King, Skylar D and Torkian, Pooya and Chen, Andy C and Talaie, Reza and Chen, Shi-You and Lin, Jian},
title = {Digital light 4D printing of bioresorbable shape memory elastomers for personalized biomedical implantation},
journal = {Acta Biomaterialia},
year = {2024},
volume = {177},
pages = {165--177},
doi = {10.1016/j.actbio.2024.02.009}
}
EUVIMED