EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Copying a soft lithography master mold using an inexpensive, hobby-use UV-curable resin

Kazuo Hosokawa, Hiroshi Kasuga, Hitoshi Ohmori

Analytical Sciences · 2026-08 · 42 (8) · 787-793

DOI: 10.1007/s44211-026-00920-2 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Analytical Sciences, online erschienen am 30.04.2026. Verfasst von Kazuo Hosokawa und 2 weiteren Autor:innen. Beteiligte Einrichtung: Materials Fabrication Laboratory, RIKEN Pioneering Research Institute, 2-1 Hirosawa, Wako, Saitama, 351-0198, Japan. k-hoso@riken.jp. Die Arbeit nennt 20 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Japan Society for the Promotion of Science.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Poly(dimethylsiloxane) (PDMS) is the most widely used material for microfluidic chips because of its advantageous properties including easy fabrication through soft lithography, which means pattern transfer technique from microfabricated master molds. However, most of the master molds are made of a silicon wafer and a photoresist layer, and have two major disadvantages: (1) the fabrication process is complicated and requires specialized facilities, and (2) the fabricated master molds are fragile. Here, we describe a simple fabrication technique to produce a robust master mold by pattern transfer from an existing PDMS chip to an inexpensive, hobby-use UV-curable resin (UV resin). The process requires no specialized facilities or hazardous chemicals. The test pattern consisted of microchannels with a cross-section of 100 µm × 25 µm and a total area of 30 mm × 30 mm. This pattern was faithfully transferred from the PDMS surface to the UV resin. The inaccuracy of the solidified UV resin was evaluated to be smaller than the measurement error (< 0.2%). The UV resin mold was subsequently tested for the soft lithography of a next-generation PDMS chip. For successful soft lithography, the UV resin mold required heat treatment at 60 °C for at least 48 h prior to use. Without this treatment, substantial damage was observed on both the PDMS and the UV resin surfaces. This problem was probably caused by the inhibition of PDMS curing due to unreacted components of the UV resin remaining on the surface. The technique presented here provides a simple and low-cost route for the repetitive fabrication of identical PDMS microfluidic chips for various research fields.

Schlagwörter

Stichwörter der Autor:innen

FabricationMicrofluidic chipPDMSPoly(dimethylsiloxane)Soft lithographyUV resin

Autor:innen und Institutionen

  • Materials Fabrication Laboratory, RIKEN Pioneering Research Institute, 2-1 Hirosawa, Wako, Saitama, 351-0198, Japan. k-hoso@riken.jp.
  • Materials Fabrication Laboratory, RIKEN Pioneering Research Institute, 2-1 Hirosawa, Wako, Saitama, 351-0198, Japan.

Förderung

  • Japan Society for the Promotion of Science

Zitieren

APA

Hosokawa, K., Kasuga, H., & Ohmori, H. (2026). Copying a soft lithography master mold using an inexpensive, hobby-use UV-curable resin. Analytical Sciences, 42(8), 787-793. https://doi.org/10.1007/s44211-026-00920-2

Vancouver

Hosokawa K, Kasuga H, Ohmori H. Copying a soft lithography master mold using an inexpensive, hobby-use UV-curable resin. Analytical Sciences. 2026;42(8):787-793. doi:10.1007/s44211-026-00920-2

BibTeX
@article{Hosokawa2026,
  author = {Hosokawa, Kazuo and Kasuga, Hiroshi and Ohmori, Hitoshi},
  title = {Copying a soft lithography master mold using an inexpensive, hobby-use UV-curable resin},
  journal = {Analytical Sciences},
  year = {2026},
  volume = {42},
  number = {8},
  pages = {787--793},
  doi = {10.1007/s44211-026-00920-2}
}
Kostenlos starten →