Effect of SiC addition on laser-based CoNi binary alloy coatings on Ti-6Al-4V alloy
Emergent Materials · 2024-10 · 7 (5) · 2117-2128
DOI: 10.1007/s42247-024-00733-x ↗Kurz gefasst
Fachartikel in der Zeitschrift Emergent Materials, online erschienen am 07.05.2024. Verfasst von Olanrewaju Seun Adesina und 6 weiteren Autor:innen. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 42 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Tshwane University of Technology.
Abstract (Originalsprache)
This research explores the impact of variations in laser scanning speed and the incorporation levels of SiC-Ni-Co powders on Ti-6Al-4V alloy using laser surface cladding technique. Key parameters, including a consistent laser power of 700 W, a 4 mm beam spot size, a powder feed rate of 1.0 g/min, and a gas flow rate of 3 L/min, along with fixed powder compositions, were maintained. The laser scanning speeds were adjusted to 0.4 m/min, 0.8 m/min, and 1.2 m/min. Microstructural analyses were carried out using scanning electron microscopy (SEM) while Vickers microhardness was employed to assess coating hardness, and corrosion properties were evaluated using a linear potentiodynamic polarization technique. Following the corrosion attack, the protective oxides formed were identified through SEM and X-ray diffractometer (XRD). The results revealed a strong metallurgical relationship between the clad layer and the substrate, demonstrating the effectiveness of the laser-clad technique. Particularly, the highest laser scan speed exhibited the most significant improvements in hardness and corrosion resistance. The coatings displayed an average hardness value of 1269.20 HV 0.1 , a notable fourfold increase compared to the substrate's value of 334 HV 0.1 . Concerning corrosion, a clear correlation emerged between scan speed and polarization resistance, confirming that higher scan speeds could lead to enhanced polarization resistance.
Förderung
- Tshwane University of Technology
Zitieren
APA
Adesina, O. S., Popoola, A. P., Farotade, G. A., Obadele, B. A., Sanyaolu, O. O., Jeje, S. O., & Rominiyi, A. L. (2024). Effect of SiC addition on laser-based CoNi binary alloy coatings on Ti-6Al-4V alloy. Emergent Materials, 7(5), 2117-2128. https://doi.org/10.1007/s42247-024-00733-x
Vancouver
Adesina OS, Popoola AP, Farotade GA, Obadele BA, Sanyaolu OO, Jeje SO, et al. Effect of SiC addition on laser-based CoNi binary alloy coatings on Ti-6Al-4V alloy. Emergent Materials. 2024;7(5):2117-2128. doi:10.1007/s42247-024-00733-x
BibTeX
@article{Adesina2024,
author = {Adesina, Olanrewaju Seun and Popoola, Abimbola Patricia and Farotade, Gabriel Ayokunle and Obadele, Babatunde Abiodun and Sanyaolu, Olufemi Oluseun and Jeje, Samson Olaitan and Rominiyi, Azeez Lawan},
title = {Effect of SiC addition on laser-based CoNi binary alloy coatings on Ti-6Al-4V alloy},
journal = {Emergent Materials},
year = {2024},
volume = {7},
number = {5},
pages = {2117--2128},
doi = {10.1007/s42247-024-00733-x}
}
EUVIMED