EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Combining 3D printing and injection moulding for the fabrication of polymer micro-components with internal hollow features

Jeremy Farrugia, Pierre Vella, Arif Rochman

Progress in Additive Manufacturing · 2024-10 · 9 (5) · 1353-1364

DOI: 10.1007/s40964-024-00616-x ↗

Kurz gefasst

Fachartikel in der Zeitschrift Progress in Additive Manufacturing, online erschienen am 10.04.2024. Verfasst von Jeremy Farrugia und 2 weiteren Autor:innen. Die Arbeit wurde bisher 10-mal zitiert (Crossref) und nennt 51 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Malta Council for Science and Technology, University of Malta.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

There is a need to cost-effectively produce polymer components with meso/micro-scale internal geometries with high replication accuracy without the use of post-processing steps. A possible process chain to produce such polymer components with internal hollow features is by combining the 3D printing (3DP) and micro-injection moulding (MIM) processes. To date, no studies were carried out to explore the feasibility of such a process chain. Consequently, this experimental study investigated the use of the 3DP lost-cores that are over-moulded using the MIM process. The first step involved the production of lost-core from a soluble polymer material where three different materials were studied: two filament-based materials (Xioneer VXL130 and AquaSys180) and one resin-based material (IM-HDT-WS). The filament-based materials were printed on an Ultimaker S5 (filament fused fabrication) and the resin-based material was printed using an Asiga Max X27 (digital light processing). In the second step, the lost core was then over-moulded with polymethyl methacrylate (PMMA) using the MIM process. After demoulding, the internal core was then dissolved using the respective dissolution method of each material to achieve a part with meso/micro scale internal features. Investigations carried out at the different stages of the process chain revealed that the best dimensional accuracy was achieved when using the IM-HDT-WS material in the 3DP of the lost-cores and their subsequent over-moulding to form the case study part internal geometry. In particular, the dimensional analysis of the replicated IM-HDT-WS lost-core geometries onto the over-moulded PMMA revealed a difference of 0% in diameter and − 3.17% in bifurcation angle of the Y1.6 channel and a difference of + 4.88% in diameter and + 11.48% in bifurcation angle of the Y0.8 channels when compared to the respective 3DP core dimensional values prior to encapsulation. However, dissolution tests revealed that the filament-based material, the Xioneer VXL130, achieved a dissolution rate of 3.5 and 4.5 h for the Y1.6 and Y0.8 channel, respectively, which was marginally faster than that of the IM-HDT-WS.

Förderung

  • Malta Council for Science and Technology
  • University of Malta

Zitieren

APA

Farrugia, J., Vella, P., & Rochman, A. (2024). Combining 3D printing and injection moulding for the fabrication of polymer micro-components with internal hollow features. Progress in Additive Manufacturing, 9(5), 1353-1364. https://doi.org/10.1007/s40964-024-00616-x

Vancouver

Farrugia J, Vella P, Rochman A. Combining 3D printing and injection moulding for the fabrication of polymer micro-components with internal hollow features. Progress in Additive Manufacturing. 2024;9(5):1353-1364. doi:10.1007/s40964-024-00616-x

BibTeX
@article{Farrugia2024,
  author = {Farrugia, Jeremy and Vella, Pierre and Rochman, Arif},
  title = {Combining 3D printing and injection moulding for the fabrication of polymer micro-components with internal hollow features},
  journal = {Progress in Additive Manufacturing},
  year = {2024},
  volume = {9},
  number = {5},
  pages = {1353--1364},
  doi = {10.1007/s40964-024-00616-x}
}
Kostenlos starten →