EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Mechanical properties and damage evolution characteristics of composite rock mass with prefabricated fractures

Hukun Wang, Jun Hu, Zhiguo Xia, Chengwei Liu, Bin Yang, Bing Chen, Linbin Zhang, Xinrong Wang

Computational Particle Mechanics · 2024-10 · 11 (5) · 1937-1957

DOI: 10.1007/s40571-024-00719-w ↗

Kurz gefasst

Fachartikel in der Zeitschrift Computational Particle Mechanics, 2024-10. Verfasst von Hukun Wang und 7 weiteren Autor:innen. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 44 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: National Natural Science Foundation of China, Natural Science Foundation of Liaoning Province, Education Department Foundation of Liaoning Province.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this study, the influence of fractures on the mechanical properties and cracking behavior of composite rock mass was investigated by preparing rock-like specimens of composite rock mass with different dip angles of fractures using customized molds. The failure process of the sample was recorded using a camera, and the rock failure process analysis technology was used for quantitative investigation of the mechanical mechanism of crack evolution during the loading process of the sample. Based on the experimental results, the crack propagation and coalescence modes of fractured composite rock mass were analyzed, and the distribution laws of contact force chain and maximum principal stress during initial crack initiation were studied from the microscopic perspective. The results show that with the increase in fracture dip angle, when the fracture is located in hard rock, the peak strength of the specimen decreases first, then increases and then decreases. When the fracture is located in both soft rock and hard rock, the peak strength of the specimen is mainly controlled by the fracture in soft rock. The initial crack mainly occurs at the tip of the soft rock fracture, and then converges with the cracks developed at the end of the hard rock fracture through the interface. The crack propagation type and coalescence mode are affected by the joint action of the fracture dip angle and position. In total, eight crack propagation types and six crack coalescence modes were observed during the failure process. The maximum principal stress concentration area is distributed around the fracture and is “butterfly” type. With the increase in fracture dip angle, the maximum principal stress concentration area gets gradually deflected perpendicular to the fracture direction, and does not pass through the interface of soft and hard rocks. The existence of the interface prevents the transmission of stress to a certain extent.

Förderung

  • National Natural Science Foundation of China
  • Natural Science Foundation of Liaoning Province
  • Education Department Foundation of Liaoning Province
  • Outstanding Young Scientific and Technological Talents Project of Liaoning University of Science and Technology

Zitieren

APA

Wang, H., Hu, J., Xia, Z., Liu, C., Yang, B., Chen, B., Zhang, L., & Wang, X. (2024). Mechanical properties and damage evolution characteristics of composite rock mass with prefabricated fractures. Computational Particle Mechanics, 11(5), 1937-1957. https://doi.org/10.1007/s40571-024-00719-w

Vancouver

Wang H, Hu J, Xia Z, Liu C, Yang B, Chen B, et al. Mechanical properties and damage evolution characteristics of composite rock mass with prefabricated fractures. Computational Particle Mechanics. 2024;11(5):1937-1957. doi:10.1007/s40571-024-00719-w

BibTeX
@article{Wang2024,
  author = {Wang, Hukun and Hu, Jun and Xia, Zhiguo and Liu, Chengwei and Yang, Bin and Chen, Bing and Zhang, Linbin and Wang, Xinrong},
  title = {Mechanical properties and damage evolution characteristics of composite rock mass with prefabricated fractures},
  journal = {Computational Particle Mechanics},
  year = {2024},
  volume = {11},
  number = {5},
  pages = {1937--1957},
  doi = {10.1007/s40571-024-00719-w}
}
Kostenlos starten →