Co-Form meltblown process: Part III – effect of process parameters on shedding of particles
Fibers and Polymers · 21.11.2026
DOI: 10.1007/s12221-026-01632-0 ↗Kurz gefasst
Fachartikel in der Zeitschrift Fibers and Polymers, online erschienen am 21.11.2026. Verfasst von Md Nur Uddin und 2 weiteren Autor:innen. Die Arbeit nennt 10 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Nonwovens Institute, North Carolina State University.
Abstract (Originalsprache)
This study, the third in a series, investigates the effect of processing parameters on the shedding stability of aluminum oxide (AO) particles within co-form meltblown nonwoven webs produced from Pebax® 2533, a polyether block amide elastomer. Building on the loading efficiency and spatial distribution findings of Parts I and II, particle retention was quantified using a Ro-Tap agitation protocol under standardized mechanical stress. Overall shedding was low across all conditions, ranging from 0.15 to 2.43% by mass. Particle size was the primary determinant of retention: 600 μm particles were the most stable (0.3–0.8% loss), while 300 μm particles showed the highest losses (up to 2.4%). Insertion distance produced a counterintuitive, non-monotonic result: shedding was lowest at 15 cm (mean 0.73%), highest at 38 cm (mean 1.28%), and intermediate at 60 cm (mean 0.92%). This behavior is explained by three physically distinct retention mechanisms that operate at different distances from the die. At 15 cm, fibers are still near their crystallization temperature (∼T cryst = 110 °C) due to the 220 °C process air, enabling Frenkel sintering and encapsulation of the particles as the fiber cools and solidifies around them. At 38 cm, fully solidified fibers undergo elastic rebound on contact with the rigid AO particles, forming only a sparse mechanical cage with weak retention—particularly for smaller particles that intercept few fibers. At 60 cm, particles settle into a pre-formed, consolidated fiber mat rather than encountering high-velocity flying fibers, resulting in better passive entrapment than at 38 cm despite an identical fiber thermal state. Air pressure (6–10 psi) had no statistically significant effect on shedding ( p = 0.51), confirming that it does not alter the retention regime, only the web structure. Silane surface treatment of 425 μm particles did not significantly change mean shedding but substantially reduced sample-to-sample variability. These results complete a process–structure–property framework for designing stable, high-performance co-form nonwovens, and establish insertion distance as the primary lever for controlling both particle loading and retention.
Förderung
- Nonwovens Institute, North Carolina State University
Zitieren
APA
Uddin, M. N., Maze, B., & Pourdeyhimi, B. (2026). Co-Form meltblown process: Part III – effect of process parameters on shedding of particles. Fibers and Polymers. https://doi.org/10.1007/s12221-026-01632-0
Vancouver
Uddin MN, Maze B, Pourdeyhimi B. Co-Form meltblown process: Part III – effect of process parameters on shedding of particles. Fibers and Polymers. 2026. doi:10.1007/s12221-026-01632-0
BibTeX
@article{Uddin2026,
author = {Uddin, Md Nur and Maze, Benoit and Pourdeyhimi, Behnam},
title = {Co-Form meltblown process: Part III – effect of process parameters on shedding of particles},
journal = {Fibers and Polymers},
year = {2026},
doi = {10.1007/s12221-026-01632-0}
}
EUVIMED