Does fast sintering affect the optical properties, fracture strength, and microstructure of monolithic zirconia?
Odontology · 2026
DOI: 10.1007/s10266-025-01110-8 ↗Kurz gefasst
Fachartikel in der Zeitschrift Odontology, 2026. Verfasst von Mustafa Ayata und 2 weiteren Autor:innen. Beteiligte Einrichtung: Private Practice, Ortoperio Oral and Dental Health Polyclinic, Kocasinan, Kayseri, Türkiye. Hauptthemen laut MEDLINE: Zirconium, Dental Materials, Ceramics. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 47 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Erciyes University.
Abstract (Originalsprache)
The purpose of this study was to examine the influence of fast sintering on the optical properties, fracture strength, and microstructure of monolithic zirconia (MZ) ceramics. After 20 disc-shaped and 4 square-shaped samples from the MZ block were machined in the CAM device, groups were created by the sintering procedure in accordance with the manufacturer's recommendations: Standard (Grup S; disc-shaped n = 10 square-shaped n = 2) and fast (Grup F; disc-shaped n = 10 square-shaped n = 2). Then, hydrothermal aging was applied to all samples. To calculate translucency, opalescence, and fluorescence values, the LabCh color data of the samples were defined using spectrophotometers. The disc samples were biaxially fracture tested, and the values were determined. The chemical content, grain size (GS), and phase composition of the square-shaped samples were analyzed, respectively. Since the grain size did not conform to the normal distribution, the Mann–Whitney U test was used for statistical analysis, and all other variables were analyzed by an independent sample t test ( α = 0.05). The sintering procedure affected translucency, opalescence, fracture strength, and GS significantly ( P < 0.05), but not fluorescence ( P > 0.05). While both groups had similar crystal structures, there were some minor differences in chemical content. All samples had a higher fracture strength than the ISO 6872 standard recommends. The sintering procedure had no clinically significant effect on the optical properties of MZ. The fast sintering procedure of MZ can be recommended.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Private Practice, Ortoperio Oral and Dental Health Polyclinic, Kocasinan, Kayseri, Türkiye.
- Department of Prosthodontics, Faculty of Dentistry, Erciyes University, Melikgazi, Kayseri, Türkiye.
- Department of Prosthodontics, Faculty of Dentistry, Erciyes University, Melikgazi, Kayseri, Türkiye. ravzaeraslan@erciyes.edu.tr.
Förderung
- Erciyes University
Zitieren
APA
Ayata, M., Albayrak, H., & Eraslan, R. (2026). Does fast sintering affect the optical properties, fracture strength, and microstructure of monolithic zirconia?. Odontology. https://doi.org/10.1007/s10266-025-01110-8
Vancouver
Ayata M, Albayrak H, Eraslan R. Does fast sintering affect the optical properties, fracture strength, and microstructure of monolithic zirconia?. Odontology. 2026. doi:10.1007/s10266-025-01110-8
BibTeX
@article{Ayata2026,
author = {Ayata, Mustafa and Albayrak, Haydar and Eraslan, Ravza},
title = {Does fast sintering affect the optical properties, fracture strength, and microstructure of monolithic zirconia?},
journal = {Odontology},
year = {2026},
doi = {10.1007/s10266-025-01110-8}
}
EUVIMED