EUVIMEDEUVIMED entdecken
Übersichtsarbeit

Surface characteristics of resin composite cores and bond strength to CAD/CAM resin matrix glass–ceramic restorations after different treatment protocols

Leandro Maruki Pereira, Bárbara Inácio de Melo, Verena Paula Stern Netto, Paola Bernardes, Luís Henrique Araújo Raposo, Marcel Santana Prudente, Flávio Domingues das Neves

Odontology · 2025

DOI: 10.1007/s10266-024-01034-9 ↗

Kurz gefasst

Übersichtsarbeit in der Zeitschrift Odontology, 2025. Verfasst von Leandro Maruki Pereira und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Occlusion, Fixed Prosthodontics and Dental Materials, School of Dentistry, Federal University of Uberlandia, Av. Pará, 1720, Bloco 4L, …. Hauptthemen laut MEDLINE: Composite Resins, Dental Bonding, Ceramics, Computer-Aided Design. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 41 Literaturangaben. Gefördert von: Research Support Foundation of the State of Minas Gerais.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The purpose of this study was to evaluate the impact of various mechanical surface treatments on the surface roughness and microtensile bond strength (µTBS) of aged composite resin cores bonded to CAD/CAM restorations. Composite resin specimens (Filtek Z350 XT, 3M-ESPE/Solventum) were thermally aged and subsequently divided into four groups (n = 36) according to surface treatments: UI-cleaning with ultrasonic diamond tip; AO-sandblasting with 50 µm Al2O3; DB-cleaning with diamond burs; and CG-positive control group, without aging or surface treatment. Surface roughness was assessed using a profilometer and interferometer, with measurements taken on both sides of each specimen (n = 12). The surface characteristics were further analyzed through scanning electron microscopy (SEM) (n = 12). In addition, PMMA blocks were temporarily cemented (n = 12) onto the resin blocks, and after surface treatments, resin matrix glass-ceramic blocks were adhesively luted with dual-cure resin cement (RelyX Ultimate, 3 M-ESPE/ Solventum, St. Paul, MN, USA) to the resin composite substrates. The CG specimens were adhesively luted to the indirect restorations without temporary restorations or surface treatment. After luting, the specimens were sectioned and tested for µTBS. The results (p = 0.05) from the profilometry and interferometry analyses indicated the highest surface roughness values for the DB group, followed by AO, UI, and CG. SEM analysis revealed marked morphological differences among the groups. Regarding µTBS, the GC specimens (25.78 ± 5.70 MPa) and UI specimens (25.56 ± 11.36 MPa) exhibited statistically similar values, which were superior to those of the AO (12.25 ± 4.34 MPa) and DB (13.16 ± 5.59 MPa) groups (p < 0.001), which showed comparable results. In conclusion, the use of ultrasonic diamond tips resulted in the most favorable outcomes in terms of cleaning effectiveness, surface roughness, and bond strength among the surface treatments analyzed for resin composite cores.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Composite ResinsDental BondingCeramicsComputer-Aided DesignDental Restoration, PermanentSurface PropertiesTensile StrengthMaterials TestingMicroscopy, Electron, ScanningResin Cements

Stichwörter der Autor:innen

AdhesionBondingComposite resinsSurface roughness

Substanzen

Composite ResinsGlass ceramicsResin Cements

Autor:innen und Institutionen

  • Department of Occlusion, Fixed Prosthodontics and Dental Materials, School of Dentistry, Federal University of Uberlandia, Av. Pará, 1720, Bloco 4L, Anexo A, sala 4LA-42, Campus Umuarama, Uberlândia, Minas Gerais, 38405…
  • Department of Operative Dentistry and Dental Materials, School of Dentistry, Federal University of Uberlândia, Uberlândia, MG, Brazil.

Förderung

  • Research Support Foundation of the State of Minas Gerais

Zitieren

APA

Pereira, L. M., de Melo, B. I., Netto, V. P. S., Bernardes, P., Raposo, L. H. A., Prudente, M. S., & das Neves, F. D. (2025). Surface characteristics of resin composite cores and bond strength to CAD/CAM resin matrix glass–ceramic restorations after different treatment protocols. Odontology. https://doi.org/10.1007/s10266-024-01034-9

Vancouver

Pereira LM, de Melo BI, Netto VPS, Bernardes P, Raposo LHA, Prudente MS, et al. Surface characteristics of resin composite cores and bond strength to CAD/CAM resin matrix glass–ceramic restorations after different treatment protocols. Odontology. 2025. doi:10.1007/s10266-024-01034-9

BibTeX
@article{Pereira2025,
  author = {Pereira, Leandro Maruki and de Melo, Bárbara Inácio and Netto, Verena Paula Stern and Bernardes, Paola and Raposo, Luís Henrique Araújo and Prudente, Marcel Santana and das Neves, Flávio Domingues},
  title = {Surface characteristics of resin composite cores and bond strength to CAD/CAM resin matrix glass–ceramic restorations after different treatment protocols},
  journal = {Odontology},
  year = {2025},
  doi = {10.1007/s10266-024-01034-9}
}
Kostenlos starten →