A combined 4D flow MR imaging and fluid–structure interaction analysis of ascending thoracic aortic aneurysms
Biomechanics and Modeling in Mechanobiology · 2025-06 · 24 (3) · 829-844
DOI: 10.1007/s10237-025-01939-6 ↗Kurz gefasst
Fachartikel in der Zeitschrift Biomechanics and Modeling in Mechanobiology, online erschienen am 11.03.2025. Verfasst von Yu Zhu und 7 weiteren Autor:innen. Beteiligte Einrichtung: Department of Chemical Engineering, Imperial College London, London, UK. Hauptthemen laut MEDLINE: Aortic Aneurysm, Thoracic, Magnetic Resonance Imaging, Aorta, Imaging, Three-Dimensional. Die Arbeit wurde bisher 18-mal zitiert (Crossref) und nennt 46 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Heart Research UK, Medical Research Council, British Heart Foundation.
Abstract (Originalsprache)
This study aimed to characterize the altered hemodynamics and wall mechanics in ascending thoracic aortic aneurysms (ATAA) by employing fully coupled two-way fluid–structure interaction (FSI) analyses. Our FSI models incorporated hyperelastic wall mechanical properties, prestress, and patient-specific inlet velocity profiles (IVP) extracted from 4D flow magnetic resonance imaging (MRI). By performing FSI analyses on 7 patient-specific ATAA models and 6 healthy aortas, the primary objective of the study was to compare hemodynamic and biomechanical features in ATAA versus healthy controls. A secondary objective was to examine the need for 4D flow MRI-derived IVP in FSI simulations by comparing results with those using two commonly adopted idealized IVPs: Flat-IVP and Para-IVP for selected cases. Our results show that, compared to the healthy aortas, the ATAA models exhibited highly disturbed blood flow in the ascending aorta. Consequently, maximum turbulent kinetic energy (TKE) at peak systole (155.0 ± 188.4 Pa) and maximum time-averaged wall shear stress (TAWSS) (8.6 ± 6.5 Pa) were significantly higher in the ATAA cohort, compared to 0.6 ± 0.5 Pa and 2.8 ± 0.7 Pa in the healthy aortas. Peak wall stress was also nearly doubled in the ATAA group (414 ± 108 kPa vs. 215 ± 31 kPa). Additionally, comparisons of simulation results across models with different IVPs underscore the importance of prescribing 3D-IVP at the inlet, especially for ATAA cases. Using idealized IVPs in two selected ATAA models (P1 and P7) substantially reduced the maximum TKE from 571 Pa to 0.01 Pa (Flat-IVP) and 0.02 Pa (Para-IVP) in P1 and from 73 Pa to 0.01 Pa (Flat-IVP) and 0.08 Pa (Para-IVP) in P7, while the maximum TAWSS in the ascending aorta decreased from 9.6 Pa to 0.7 Pa (Flat-IVP) and 0.9 Pa (Para-IVP) in P1, and from 3.6 Pa to 1.2 Pa and 0.9 Pa, respectively, in P7. Moreover, idealized IVPs also caused the peak wall stress to reduce by up to 11.5% in P1 with severe aortic valve stenosis, and by up to 2% in P7 with mild aortic regurgitation. These results highlight the importance of FSI simulations combined with 4D flow MRI in capturing realistic hemodynamic and biomechanical changes in aneurysmal aortas.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Chemical Engineering, Imperial College London, London, UK.
- National Heart and Lung Institute, Imperial College London, London, UK.
- Department of Biomechanical Engineering, Delft University of Technology, Delft, Netherlands.
- Department of Surgery and Cancer, Imperial College London, London, UK.
- MRC London Institute of Medical Sciences, Imperial College London, London, UK.
- Department of Chemical Engineering, Imperial College London, London, UK. yun.xu@imperial.ac.uk.
Förderung
- Heart Research UK
- Medical Research Council
- British Heart Foundation
- National Institute for Health Research (NIHR) Imperial College Biomedical Research Centre
Zitieren
APA
Zhu, Y., Armour, C., Li, B., Pirola, S., Salmasi, Y., Athanasiou, T., O'Regan, D. P., & Xu, X. Y. (2025). A combined 4D flow MR imaging and fluid–structure interaction analysis of ascending thoracic aortic aneurysms. Biomechanics and Modeling in Mechanobiology, 24(3), 829-844. https://doi.org/10.1007/s10237-025-01939-6
Vancouver
Zhu Y, Armour C, Li B, Pirola S, Salmasi Y, Athanasiou T, et al. A combined 4D flow MR imaging and fluid–structure interaction analysis of ascending thoracic aortic aneurysms. Biomechanics and Modeling in Mechanobiology. 2025;24(3):829-844. doi:10.1007/s10237-025-01939-6
BibTeX
@article{Zhu2025,
author = {Zhu, Yu and Armour, Chlöe and Li, Binghuan and Pirola, Selene and Salmasi, Yousuf and Athanasiou, Thanos and O'Regan, Declan P and Xu, Xiao Yun},
title = {A combined 4D flow MR imaging and fluid–structure interaction analysis of ascending thoracic aortic aneurysms},
journal = {Biomechanics and Modeling in Mechanobiology},
year = {2025},
volume = {24},
number = {3},
pages = {829--844},
doi = {10.1007/s10237-025-01939-6}
}
EUVIMED