Influence of silica nanoparticle sedimentation on the mechanical, surface properties and trueness of DLP-printed dental resin
Clinical Oral Investigations · 28.05.2026 · 30 (6)
DOI: 10.1007/s00784-026-06941-5 ↗Kurz gefasst
Fachartikel in der Zeitschrift Clinical Oral Investigations, online erschienen am 28.05.2026. Verfasst von Yifan Ma und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, College of Dentistry, Yonsei University, 50-1 Yonsei-ro, Seodaemun-gu, Seoul, 03722, Republic of Korea. Hauptthemen laut MEDLINE: Silicon Dioxide, Nanoparticles, Printing, Three-Dimensional, Composite Resins. Die Arbeit nennt 57 Literaturangaben. Gefördert von: Ministry of Science and ICT, South Korea.
Abstract (Originalsprache)
OBJECTIVES: This study investigated the gravitational sedimentation of silica nanoparticles in DLP-printed dental resins and assessed its impact on filler distribution, DC, mechanical and surface properties and printing trueness. MATERIALS AND METHODS: Dental resin containing 1 wt% SiNPs was printed via DLP printing into 1 mm-thick disks at build heights ranging from 1 to 15 mm above the platform. SiNP distribution was analyzed by SEM-EDS. DC, Vickers hardness, contact angle, surface roughness (Ra), and ΔE were measured and correlated with local Si concentrations (n = 5). The printed specimens from each build height were randomly assigned to different tests. Printing trueness (n = 15) was measured using digital superimposition analysis of dental crowns by RMS values. Dental resin without SiNPs served as controls. One-way ANOVA with Tukey's post-hoc test, linear regression and t-test were used for statistical analysis. RESULTS: SEM-EDS confirmed a linear increase in Si concentration with build height in the 1 wt% group (R2 = 0.8654). In the SiNP group, DC and hardness increased significantly with build height (R2 = 0.3680, R2 = 0.7964), while water contact angle and surface roughness decreased (R2 = 0.8432, R2 = 0.1505). Trueness decreased at higher build heights in the 1 wt% group (p < 0.05). The control group showed no such build height-dependent trends. CONCLUSIONS: Sedimentation during DLP induces predictable vertical nanoparticle gradients, which in turn systematically influence DC, mechanical strength, hydrophilicity, surface smoothness, and printing trueness. CLINICAL RELEVANCE: Nanoparticle sedimentation creates vertical property gradients within DLP-printed restorations. This causes heterogeneous mechanical and surface performance, potentially leading to localized weakness or marginal discrepancies. Clinicians should optimize print orientation to position functionally critical surfaces at appropriate build heights and implement mid-print homogenization to minimize sedimentation effects.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Department of Prosthodontics, College of Dentistry, Yonsei University, 50-1 Yonsei-ro, Seodaemun-gu, Seoul, 03722, Republic of Korea.
- Oral Science Research Center, College of Dentistry, Yonsei University, 50-1 Yonsei-ro, Seodaemun-gu, Seoul, 03722, Republic of Korea.
- Department of Prosthodontics, College of Dentistry, Yonsei University, 50-1 Yonsei-ro, Seodaemun-gu, Seoul, 03722, Republic of Korea. gomyou@yuhs.ac.
Förderung
- Ministry of Science and ICT, South Korea
Zitieren
APA
Ma, Y., Jin, G., Chen, D., Zhang, Z., Liu, Y., Lim, J. H., & Kim, J. E. (2026). Influence of silica nanoparticle sedimentation on the mechanical, surface properties and trueness of DLP-printed dental resin. Clinical Oral Investigations, 30(6). https://doi.org/10.1007/s00784-026-06941-5
Vancouver
Ma Y, Jin G, Chen D, Zhang Z, Liu Y, Lim JH, et al. Influence of silica nanoparticle sedimentation on the mechanical, surface properties and trueness of DLP-printed dental resin. Clinical Oral Investigations. 2026;30(6). doi:10.1007/s00784-026-06941-5
BibTeX
@article{Ma2026,
author = {Ma, Yifan and Jin, Gan and Chen, Di and Zhang, Zhihao and Liu, Yunqi and Lim, Jung-Hwa and Kim, Jong-Eun},
title = {Influence of silica nanoparticle sedimentation on the mechanical, surface properties and trueness of DLP-printed dental resin},
journal = {Clinical Oral Investigations},
year = {2026},
volume = {30},
number = {6},
doi = {10.1007/s00784-026-06941-5}
}
EUVIMED