EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Structural response of mandibular first molars in the presence of proximal contacts: finite element analysis with antagonist teeth and alternative loading applications

Saúl Dorado iD, Jesús R Jimenez-Octavio iD, Paula Riaza, Ove A Peters iD, Ana Arias iD

Clinical Oral Investigations · 2025

DOI: 10.1007/s00784-025-06290-9 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Clinical Oral Investigations, 2025. Verfasst von Saúl Dorado und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, Escuela Técnica Superior de Ingeniería ICAI, Universidad Pontificia Comillas, Madrid, Spain. Hauptthemen laut MEDLINE: Finite Element Analysis, Molar, Dental Stress Analysis, Bite Force. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 60 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objectives

To compare the mechanical responses of a mandibular molar under functional loads using antagonist teeth and different loading applications and configurations.

Methods

A cone-beam computed tomography of a human mandible and maxilla was used to build 16 different three-dimensional models, including four mandibular configurations [single-tooth model (first mandibular molar-M), and inclusion of mesial (mM), distal (Md) or both proximal contacts (mMd)] and occlusal load applications either with antagonist teeth or alternative Finite Element (FE) models [point load (PL), distributed surface load (SL) and rigid metal sphere (MS)]. FE analysis was performed. Equivalent von Mises (VM) stress was calculated along the entire dentin and periodontal ligament of the first mandibular molar. Maximum VM stresses were compared among the different mandibular configurations and loading applications.

Results

The highest and lowest VM stress at 50 and 100 N corresponded respectively to the single-tooth SL model (5.78 and 11.5 MPa) and to occlusal load application with antagonist teeth and proximal contacts (2.08 and 3.58 MPa). Maximum VM stresses were consistently located at the cervical area of the mesial root and decreased when adjacent teeth were present.

Conclusions

Highest stresses are located in the cervical area of the mesial root of mandibular molars, but the biomechanical behavior depends on the presence of proximal contacts and the loading methodologies used. Single-tooth models represent the worst structural scenario. Clinical relevance Incorporating antagonist teeth and proximal contacts into FE models enhances the biofidelity of dental biomechanics simulations, enabling more accurate extrapolation to clinical conditions.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Finite Element AnalysisMolarDental Stress AnalysisBite ForceHumansMandibleCone-Beam Computed TomographyBiomechanical PhenomenaImaging, Three-DimensionalStress, Mechanical

Stichwörter der Autor:innen

BiomechanicsDental tissueFinite element analysisFunctional loadStress distribution

Autor:innen und Institutionen

  • Department of Mechanical Engineering, Escuela Técnica Superior de Ingeniería ICAI, Universidad Pontificia Comillas, Madrid, Spain.
  • MOBIOS Lab, Institute for Research in Technology, Escuela Técnica Superior de Ingeniería ICAI, Universidad Pontificia Comillas, Madrid, Spain.
  • Department of Conservative and Prosthetic Dentistry, School of Dentistry, Complutense University, Plaza Ramon y Cajal s/n. Ciudad Universitaria, Madrid, 28040, Spain.
  • Oral Health Centre, School of Dentistry, The University of Queensland, Herston, QLD, Australia.
  • Department of Conservative and Prosthetic Dentistry, School of Dentistry, Complutense University, Plaza Ramon y Cajal s/n. Ciudad Universitaria, Madrid, 28040, Spain. aariaspa@ucm.es.

ORCID-Profile: Saúl Dorado, Jesús R Jimenez-Octavio, Ove A Peters, Ana Arias

Zitieren

APA

Dorado, S., Jimenez-Octavio, J. R., Riaza, P., Peters, O. A., & Arias, A. (2025). Structural response of mandibular first molars in the presence of proximal contacts: finite element analysis with antagonist teeth and alternative loading applications. Clinical Oral Investigations. https://doi.org/10.1007/s00784-025-06290-9

Vancouver

Dorado S, Jimenez-Octavio JR, Riaza P, Peters OA, Arias A. Structural response of mandibular first molars in the presence of proximal contacts: finite element analysis with antagonist teeth and alternative loading applications. Clinical Oral Investigations. 2025. doi:10.1007/s00784-025-06290-9

BibTeX
@article{Dorado2025,
  author = {Dorado, Saúl and Jimenez-Octavio, Jesús R and Riaza, Paula and Peters, Ove A and Arias, Ana},
  title = {Structural response of mandibular first molars in the presence of proximal contacts: finite element analysis with antagonist teeth and alternative loading applications},
  journal = {Clinical Oral Investigations},
  year = {2025},
  doi = {10.1007/s00784-025-06290-9}
}
Kostenlos starten →