EUVIMEDEUVIMED entdecken
Crossref

Efficacy of personalized 3D-printed osteotomy guide in maximizing fibular utilization and minimizing graft length for reconstruction of large mandibular defect

Lei Jiang, Hao Lin, Zhe Shao, Bing Liu, Zhixiang Ge, Lin Dai, Bo Cheng, Tianfu Wu

Clinical Oral Investigations · 2024

DOI: 10.1007/s00784-024-05519-3 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Clinical Oral Investigations, 2024. Verfasst von Lei Jiang und 7 weiteren Autor:innen. Beteiligte Einrichtung: State Key Laboratory of Oral & Maxillofacial Reconstruction and Regeneration, Key Laboratory of Oral Biomedicine Ministry of Education, Hubei Key Lab…. Hauptthemen laut MEDLINE: Mandibular Reconstruction, Free Tissue Flaps. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 23 Literaturangaben. Gefördert von: the Health Commission of Hubei Province scientific research project, Translational Medicine and Interdisciplinary Research Joint Fund of Zhongnan Hospital of Wuhan University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

OBJECTIVE: The study addresses the long-standing challenge of insufficient length in vascularized fibular flaps when reconstructing large mandibular defects that require dual-barrel grafts. Employing personalized 3D-printed osteotomy guides, the study aims to optimize fibular utilization and minimize the required graft length. MATERIAL AND METHODS: Two reconstruction methods for distal bone defects were compared: a fold-down (FD) group that employed a specialized osteotomy guide for folding down a triangular bone segment, and a traditional double-barrel (DB) group. Metrics for comparison included defect and graft lengths, as well as the graft-to-defect length ratio. Postoperative quality of life was assessed using the University of Washington Quality of Life questionnaire (UW-QoL). RESULT: Both FD and DB groups achieved successful mandibular reconstruction. Despite larger defects in the FD group (117 ± 31.35 mm vs 84 ± 35.34 mm, p = 0.028), the used fibula length was not statistically longer in the FD group. The median ratio of graft-to-defect length was also lower in the FD group (1.327 vs 1.629, p = 0.024), suggesting that FD required only 82.47% of the graft length needed in the DB approach. Quality of life scores post-surgery were comparable between the groups. CONCLUSION: Personalized 3D-printed osteotomy guides enhance fibula graft efficacy for reconstructing larger mandibular defects, necessitating shorter graft lengths while preserving postoperative quality of life. CLINICAL RELEVANCE: This study confirms the utility of 3D printing technology as an effective and precise tool in orthopedic surgery, particularly for complex reconstructions like large mandibular defects. It suggests a viable alternative that could potentially revolutionize current practices in bone grafting.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Mandibular ReconstructionFree Tissue FlapsFibulaQuality of LifeMandibleSurgical FlapsBone TransplantationOsteotomy

Stichwörter der Autor:innen

3D-printed osteotomyFibular flapsFold-downTraditional double-barrel

Autor:innen und Institutionen

  • State Key Laboratory of Oral & Maxillofacial Reconstruction and Regeneration, Key Laboratory of Oral Biomedicine Ministry of Education, Hubei Key Laboratory of Stomatology, School & Hospital of Stomatology, Wuhan Univer…
  • Department of Stomatology, Zhongnan Hospital of Wuhan University, Wuhan, People's Republic of China.
  • Department of Oral and Maxillofacial-Head and Neck Oncology, School and Hospital of Stomatology, Wuhan University, Wuhan, People's Republic of China.
  • Hubei Joye 3D High-Tech Co., Ltd, Wuhan, People's Republic of China.
  • Department of Stomatology, Wuhan No.1 Hospital, Wuhan, People's Republic of China.
  • Department of Stomatology, Zhongnan Hospital of Wuhan University, Wuhan, People's Republic of China. chengbo@znhospital.cn.

Förderung

  • the Health Commission of Hubei Province scientific research project
  • Translational Medicine and Interdisciplinary Research Joint Fund of Zhongnan Hospital of Wuhan University

Zitieren

APA

Jiang, L., Lin, H., Shao, Z., Liu, B., Ge, Z., Dai, L., Cheng, B., & Wu, T. (2024). Efficacy of personalized 3D-printed osteotomy guide in maximizing fibular utilization and minimizing graft length for reconstruction of large mandibular defect. Clinical Oral Investigations. https://doi.org/10.1007/s00784-024-05519-3

Vancouver

Jiang L, Lin H, Shao Z, Liu B, Ge Z, Dai L, et al. Efficacy of personalized 3D-printed osteotomy guide in maximizing fibular utilization and minimizing graft length for reconstruction of large mandibular defect. Clinical Oral Investigations. 2024. doi:10.1007/s00784-024-05519-3

BibTeX
@article{Jiang2024,
  author = {Jiang, Lei and Lin, Hao and Shao, Zhe and Liu, Bing and Ge, Zhixiang and Dai, Lin and Cheng, Bo and Wu, Tianfu},
  title = {Efficacy of personalized 3D-printed osteotomy guide in maximizing fibular utilization and minimizing graft length for reconstruction of large mandibular defect},
  journal = {Clinical Oral Investigations},
  year = {2024},
  doi = {10.1007/s00784-024-05519-3}
}
Kostenlos starten →