EUVIMEDEUVIMED entdecken
Crossref

3D printed scaffolds of biosilica and spongin from marine sponges: analysis of genotoxicity and cytotoxicity for bone tissue repair

Karolyne Dos Santos Jorge Sousa, Amanda de Souza, Matheus de Almeida Cruz, Lindiane Eloisa de Lima, Giovanna do Espirito Santo, Gustavo Oliva Amaral, Renata Neves Granito, Ana Claudia Renno

Bioprocess and Biosystems Engineering · 2024

DOI: 10.1007/s00449-024-03042-z ↗

Kurz gefasst

Fachartikel in der Zeitschrift Bioprocess and Biosystems Engineering, 2024. Verfasst von Karolyne Dos Santos Jorge Sousa und 7 weiteren Autor:innen. Beteiligte Einrichtung: Department of Biosciences, Federal University of São Paulo (UNIFESP), Lab 342, 136 Silva Jardim Street, Santos, SP, 11015020, Brazil. kksousa12@gmail…. Hauptthemen laut MEDLINE: Tissue Scaffolds, Porifera, Printing, Three-Dimensional. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 52 Literaturangaben. Gefördert von: Fundação de Amparo à Pesquisa do Estado de São Paulo.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Biosilica (BS) and spongin (SPG) from marine sponges are highlighted for their potential to promote bone regeneration. Moreover, 3D printing is introduced as a technology for producing bone grafts with optimized porous structures, allowing for better cell attachment, proliferation, and differentiation. Thus, this study aimed to characterize the BS and BS/SPG 3D printed scaffolds and to evaluate the biological effects in vitro. The scaffolds were printed using an ink containing 4 wt.% of sodium alginate. The physicochemical characteristics of BS and BS/SPG 3D printed scaffolds were analyzed by SEM, EDS, FTIR, porosity, evaluation of mass loss, and pH measurement. For in vitro analysis, the cellular viability of the MC3T3-E1 cell lineage was assessed using the AlamarBlue® assay and confocal microscopy, while genotoxicity and mineralization potential were evaluated through the micronucleus assay and Alizarin Red S, respectively. SEM analysis revealed spicules in BS, the fibrillar structure of SPG, and material degradation over the immersion period. FTIR indicated peaks corresponding to silicon oxide in BS samples and carbon oxide and amine in SPG samples. BS-SPG scaffolds exhibited higher porosity, while BS scaffolds displayed greater mass loss. pH measurements indicated a significant decrease induced by BS, which was mitigated by SPG over the experimental periods. In vitro studies demonstrated the biocompatibility and non-cytotoxicity of scaffold extracts. .Also, the scaffolds promoted cellular differentiation. The micronucleus test further confirmed the absence of genotoxicity. These findings suggest that 3D printed BS and BS/SPG scaffolds may possess desirable morphological and physicochemical properties, indicating in vitro biocompatibility.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Tissue ScaffoldsPoriferaPrinting, Three-DimensionalAnimalsMiceSilicon DioxideBone RegenerationPorosityCell SurvivalTissue EngineeringCell LineBone and Bones

Stichwörter der Autor:innen

3D printingBiosilicaBone scaffoldsMarine spongesSpongin

Substanzen

Silicon Dioxide

Autor:innen und Institutionen

  • Department of Biosciences, Federal University of São Paulo (UNIFESP), Lab 342, 136 Silva Jardim Street, Santos, SP, 11015020, Brazil. kksousa12@gmail.com.
  • Department of Biosciences, Federal University of São Paulo (UNIFESP), Lab 342, 136 Silva Jardim Street, Santos, SP, 11015020, Brazil.

Förderung

  • Fundação de Amparo à Pesquisa do Estado de São Paulo

Zitieren

APA

Dos Santos Jorge Sousa, K., de Souza, A., de Almeida Cruz, M., de Lima, L. E., do Espirito Santo, G., Amaral, G. O., Granito, R. N., & Renno, A. C. (2024). 3D printed scaffolds of biosilica and spongin from marine sponges: analysis of genotoxicity and cytotoxicity for bone tissue repair. Bioprocess and Biosystems Engineering. https://doi.org/10.1007/s00449-024-03042-z

Vancouver

Dos Santos Jorge Sousa K, de Souza A, de Almeida Cruz M, de Lima LE, do Espirito Santo G, Amaral GO, et al. 3D printed scaffolds of biosilica and spongin from marine sponges: analysis of genotoxicity and cytotoxicity for bone tissue repair. Bioprocess and Biosystems Engineering. 2024. doi:10.1007/s00449-024-03042-z

BibTeX
@article{DosSantosJorgeSousa2024,
  author = {Dos Santos Jorge Sousa, Karolyne and de Souza, Amanda and de Almeida Cruz, Matheus and de Lima, Lindiane Eloisa and do Espirito Santo, Giovanna and Amaral, Gustavo Oliva and Granito, Renata Neves and Renno, Ana Claudia},
  title = {3D printed scaffolds of biosilica and spongin from marine sponges: analysis of genotoxicity and cytotoxicity for bone tissue repair},
  journal = {Bioprocess and Biosystems Engineering},
  year = {2024},
  doi = {10.1007/s00449-024-03042-z}
}
Kostenlos starten →