EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Femtosecond-laser wafer slicing of n-type 4 H-SiC in double-pulse MHz burst mode

Yi-Chen Wang, Jia-Fan Kuo, Yu-Wei Chen, Chung-Wei Cheng

Applied Physics A · 2026-02 · 132 (2)

DOI: 10.1007/s00339-025-09284-2 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Applied Physics A, online erschienen am 13.01.2026. Verfasst von Yi-Chen Wang und 3 weiteren Autor:innen. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 23 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Yang Ming Chiao Tung University.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study employs a MHz burst-mode femtosecond laser to induce internal modification in 350-µm-thick n-type 4 H-SiC and to demonstrate wafer slicing using a single-/double-pulse ( N = 1–2) configuration under a fixed average power of 4.5 W and a burst repetition rate of 600 kHz (burst energy ≈ 7.5 µJ). Microstructure, surface topography, and residual stress were evaluated using scanning electron microscopy, laser-scanning confocal microscopy, and Raman spectroscopy. Single-pass line modification shows that N = 1–2 provide higher sub-pulse peak intensity, promoting lateral-crack formation that facilitates separation, whereas N = 3–5 drive deeper modification without lateral cracks. Raman measurements reveal a characteristic tension–compression residual-stress distribution, with tensile stress above and predominantly compressive stress below the lateral cracks; for example, at N = 2, the stresses are + 77.5 MPa (tension) and − 51.7 MPa (compression) at y = ± 4 μm. Full-area slicing experiments demonstrate that N = 2 shortens the step-like period and reduces the sliced-surface roughness from Sz = 47.8 μm to 32.2 μm, while maintaining a tensile strength of 3.4 MPa. Comparative Raman analysis of the two sliced surfaces further shows that laser-induced amorphous Si/C and lattice disorder accumulate mainly above the crack plane, leading to an asymmetry between the upper and lower halves of the specimen. These results establish a minimal N = 2 (double-pulse) MHz-burst configuration that enhances lateral-crack interconnection and lowers surface roughness.

Förderung

  • National Yang Ming Chiao Tung University

Zitieren

APA

Wang, Y., Kuo, J., Chen, Y., & Cheng, C. (2026). Femtosecond-laser wafer slicing of n-type 4 H-SiC in double-pulse MHz burst mode. Applied Physics A, 132(2). https://doi.org/10.1007/s00339-025-09284-2

Vancouver

Wang Y, Kuo J, Chen Y, Cheng C. Femtosecond-laser wafer slicing of n-type 4 H-SiC in double-pulse MHz burst mode. Applied Physics A. 2026;132(2). doi:10.1007/s00339-025-09284-2

BibTeX
@article{Wang2026,
  author = {Wang, Yi-Chen and Kuo, Jia-Fan and Chen, Yu-Wei and Cheng, Chung-Wei},
  title = {Femtosecond-laser wafer slicing of n-type 4 H-SiC in double-pulse MHz burst mode},
  journal = {Applied Physics A},
  year = {2026},
  volume = {132},
  number = {2},
  doi = {10.1007/s00339-025-09284-2}
}
Kostenlos starten →