EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Microstructural evolution and mechanical performance of CS1018 steel processed by additive friction stir deposition and subsequent heat treatment

Selami Emanet, Saeid Zavari, Huan Ding, Mahnaz Ensafi, Carl Schmidt, Jeff Dulik, Shengmin Guo

The International Journal of Advanced Manufacturing Technology · 2026-07 · 145 (3-4) · 2877-2894

DOI: 10.1007/s00170-026-18489-5 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The International Journal of Advanced Manufacturing Technology, online erschienen am 20.06.2026. Verfasst von Selami Emanet und 6 weiteren Autor:innen. Die Arbeit nennt 41 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Bechtel Plant Machinery, Inc. through SAM.gov, Louisiana Board of Regents for the Louisiana Materials Design Alliance.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Additive manufacturing (AM) has enabled rapid production of complex and high-performance metal components. In this study, the solid-state Additive Friction Stir Deposition (AFSD) process was demonstrated to deposit low-carbon steel CS1018. Process parameters were optimized to improve deposit quality and layer bonding. The AFSD process produced dense, metallurgically bonded CS1018 deposits with a refined ferrite–pearlite microstructure. Compared to the original CS1018 feedstock, the as-deposited material exhibited an ~ 18% lower hardness and ~ 11% lower tensile strength than the feedstock, accompanied by a ~ 78% increase in ductility. These changes are attributed to the AFSD-induced microstructural modifications: specifically, grain refinement and homogeneous dispersion of fine pearlite (Fe₃C) in a ferrite matrix. Post-deposition tempering at 210 °C and 518 °C produced only modest changes in hardness and tensile behavior relative to the as-deposited state. Changes in XRD peak breadth are consistent with reduced microstrain after tempering. Fractographic analysis revealed that the AFSD deposit’s fracture surface contained finer and more numerous dimples than the feedstock, consistent with its improved toughness. Overall, this work demonstrates that AFSD can successfully deposit low-carbon steel with good mechanical integrity. In addition, this work demonstrates that a moderate heat treatment can primarily serve to stabilize the microstructure and relief stresses without significantly altering the strength or hardness.

Förderung

  • Bechtel Plant Machinery, Inc. through SAM.gov
  • Louisiana Board of Regents for the Louisiana Materials Design Alliance

Zitieren

APA

Emanet, S., Zavari, S., Ding, H., Ensafi, M., Schmidt, C., Dulik, J., & Guo, S. (2026). Microstructural evolution and mechanical performance of CS1018 steel processed by additive friction stir deposition and subsequent heat treatment. The International Journal of Advanced Manufacturing Technology, 145(3-4), 2877-2894. https://doi.org/10.1007/s00170-026-18489-5

Vancouver

Emanet S, Zavari S, Ding H, Ensafi M, Schmidt C, Dulik J, et al. Microstructural evolution and mechanical performance of CS1018 steel processed by additive friction stir deposition and subsequent heat treatment. The International Journal of Advanced Manufacturing Technology. 2026;145(3-4):2877-2894. doi:10.1007/s00170-026-18489-5

BibTeX
@article{Emanet2026,
  author = {Emanet, Selami and Zavari, Saeid and Ding, Huan and Ensafi, Mahnaz and Schmidt, Carl and Dulik, Jeff and Guo, Shengmin},
  title = {Microstructural evolution and mechanical performance of CS1018 steel processed by additive friction stir deposition and subsequent heat treatment},
  journal = {The International Journal of Advanced Manufacturing Technology},
  year = {2026},
  volume = {145},
  number = {3-4},
  pages = {2877--2894},
  doi = {10.1007/s00170-026-18489-5}
}
Kostenlos starten →