EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Optimization of tool selection and milling parameters for enhanced machinability of hardened AISI D2 steel

Masih Paknejad, Armin Siahsarani, Mehdi Khakrangin, Bahman Azarhoushang, Robert Bösinger, Björn Becker, Rostam Hajyaghaee Khiabani, Amir Alinaghizadeh

The International Journal of Advanced Manufacturing Technology · 2026-06 · 144 (7-8) · 5747-5766

DOI: 10.1007/s00170-026-18200-8 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The International Journal of Advanced Manufacturing Technology, online erschienen am 01.05.2026. Verfasst von Masih Paknejad und 7 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 51 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Albert-Ludwigs-Universität Freiburg im Breisgau.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Milling hardened AISI D2 tool steel (60 HRC), characterized by its high hardness, toughness and wear resistance, presents significant challenges in achieving desired surface quality, minimizing burr formation and tool wear, and ensuring dimensional accuracy in medical mold machining. This research aims to identify optimal milling parameters that minimize surface roughness, tool wear, and burr formation. CBN and ceramic-coated carbide milling tools, varying in tool diameter, flute number, corner and cutting-edge radii, were evaluated under various cutting conditions. Empirical power-law models were developed to predict surface roughness (Sa) and average burr height (HB-avg), revealing that feed per tooth, cutting speed, tool diameter, axial depth of cut, and corner radius significantly influence Sa, while HB-avg was primarily governed by milling strategy, feed rate, and radial depth of cut. A radar-based multi-criteria decision-making framework was employed to select optimal tools. Subsequent experiments investigated the influence of cutting speed, feed per tooth, and milling strategy on cutting forces, surface roughness, average burr height, and microhardness. Results showed that ceramic-coated carbide tools outperformed CBN tools in roughing and finishing by providing higher material removal rates, lower tool wear and cost, and acceptable surface finish, although CBN tools yielded lower average burr height. Up milling reduced HB-avg by up to 76.8%, while increased feed per tooth deteriorated surface roughness by ~12%. Additionally, trochoidal milling produced more stable tool engagement than side milling during roughing. Optimal surface roughness was achieved under low feed per tooth and moderate cutting speed, while up milling significantly reduced burr formation. Ceramic-coated carbide tools outperformed CBN in material removal rate, tool wear, and tool cost. CBN tools resulted in lower average burr height and superior surface roughness. Empirical models identified key parameters affecting Sa and average burr height in hard milling. fz, vc, d, rc and ap were identified as the most influential parameters governing surface roughness. Average burr height was most influenced by strategy; up milling reduced it by 32%.

Förderung

  • Albert-Ludwigs-Universität Freiburg im Breisgau

Zitieren

APA

Paknejad, M., Siahsarani, A., Khakrangin, M., Azarhoushang, B., Bösinger, R., Becker, B., Khiabani, R. H., & Alinaghizadeh, A. (2026). Optimization of tool selection and milling parameters for enhanced machinability of hardened AISI D2 steel. The International Journal of Advanced Manufacturing Technology, 144(7-8), 5747-5766. https://doi.org/10.1007/s00170-026-18200-8

Vancouver

Paknejad M, Siahsarani A, Khakrangin M, Azarhoushang B, Bösinger R, Becker B, et al. Optimization of tool selection and milling parameters for enhanced machinability of hardened AISI D2 steel. The International Journal of Advanced Manufacturing Technology. 2026;144(7-8):5747-5766. doi:10.1007/s00170-026-18200-8

BibTeX
@article{Paknejad2026,
  author = {Paknejad, Masih and Siahsarani, Armin and Khakrangin, Mehdi and Azarhoushang, Bahman and Bösinger, Robert and Becker, Björn and Khiabani, Rostam Hajyaghaee and Alinaghizadeh, Amir},
  title = {Optimization of tool selection and milling parameters for enhanced machinability of hardened AISI D2 steel},
  journal = {The International Journal of Advanced Manufacturing Technology},
  year = {2026},
  volume = {144},
  number = {7-8},
  pages = {5747--5766},
  doi = {10.1007/s00170-026-18200-8}
}
Kostenlos starten →