Fabrication and evaluation of PLA/PA-HA filament for 3D printing: towards trabecular bone-compatible biomedical applications
The International Journal of Advanced Manufacturing Technology · 2025-11 · 141 (1-2) · 891-908
DOI: 10.1007/s00170-025-16623-3 ↗Kurz gefasst
Fachartikel in der Zeitschrift The International Journal of Advanced Manufacturing Technology, online erschienen am 14.10.2025. Verfasst von Afeeqa Puteri Marzuki und 6 weiteren Autor:innen. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 70 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Kementerian Pendidikan Malaysia, Universiti Teknologi MARA.
Abstract (Originalsprache)
The advancement of additive manufacturing has enabled the transition of 3D printing from a prototyping tool to a platform for producing functional, bioactive, and patient-specific implants. This study explores the fabrication and characterisation of polylactic acid (PLA) reinforced with polyamide 12 (PA12) and hydroxyapatite (HA) as composite filaments for fused deposition modeling (FDM), with a focus on bone scaffold applications. While reinforcements such as carbon, glass, and ceramic fillers have previously enhanced mechanical and thermal performance, PLA/HA composites remain hindered by brittleness. To overcome this limitation, PA12 was incorporated to improve ductility and fracture resistance while retaining the bioactivity of HA. Three formulations were prepared: PLA/20PA-10HA, PLA/30PA-10HA, and PLA/40PA-10HA, and systematically evaluated for density, functional groups (FTIR), thermal transitions (DSC), rheology, and tensile behaviour. Filament tensile testing revealed Young’s modulus values of 0.23 ± 0.06 GPa, 0.19 ± 0.06 GPa, and 0.28 ± 0.03 GPa, respectively. Among these, PLA/40PA-10HA demonstrated the most favourable balance of rheological stability and mechanical performance, leading to its selection for FDM printing. The printed cylindrical specimens achieved a compressive strength of 43.04 ± 2.78 MPa, a Young’s modulus of 0.84 ± 0.19 GPa, and a failure strain of 12.57 ± 1.18%. These properties fall within the range of human trabecular bone, indicating that the developed composite can sustain physiological loads. The findings establish a foundation for on-demand fabrication of load bearing, bioactive scaffolds through FDM, advancing the potential of chair-side manufacturing for bone tissue engineering.
Förderung
- Kementerian Pendidikan Malaysia
- Universiti Teknologi MARA
Zitieren
APA
Marzuki, A. P., Salleh, F. M., Ismail, M. H., Sulong, A. B., Abdullah, A. M., Tharazi, I., & Murat, B. I. S. (2025). Fabrication and evaluation of PLA/PA-HA filament for 3D printing: towards trabecular bone-compatible biomedical applications. The International Journal of Advanced Manufacturing Technology, 141(1-2), 891-908. https://doi.org/10.1007/s00170-025-16623-3
Vancouver
Marzuki AP, Salleh FM, Ismail MH, Sulong AB, Abdullah AM, Tharazi I, et al. Fabrication and evaluation of PLA/PA-HA filament for 3D printing: towards trabecular bone-compatible biomedical applications. The International Journal of Advanced Manufacturing Technology. 2025;141(1-2):891-908. doi:10.1007/s00170-025-16623-3
BibTeX
@article{Marzuki2025,
author = {Marzuki, Afeeqa Puteri and Salleh, Farrahshaida Mohd and Ismail, Muhammad Hussain and Sulong, Abu Bakar and Abdullah, Abdul Manaf and Tharazi, Izdihar and Murat, Bibi Intan Suraya},
title = {Fabrication and evaluation of PLA/PA-HA filament for 3D printing: towards trabecular bone-compatible biomedical applications},
journal = {The International Journal of Advanced Manufacturing Technology},
year = {2025},
volume = {141},
number = {1-2},
pages = {891--908},
doi = {10.1007/s00170-025-16623-3}
}
EUVIMED