EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

The influence of a large build area on the microstructure and mechanical properties of PBF-LB Ti-6Al-4 V alloy

Axieh Joy I Bagasol, Frederico R Kaschel, Saranarayanan Ramachandran, Wajira Mirihanage, David J Browne, Denis P Dowling

The International Journal of Advanced Manufacturing Technology · 2023-03 · 125 (3-4) · 1355-1369

DOI: 10.1007/s00170-022-10671-9 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The International Journal of Advanced Manufacturing Technology, online erschienen am 06.01.2023. Verfasst von Axieh Joy I Bagasol und 5 weiteren Autor:innen. Beteiligte Einrichtung: School of Mechanical & Materials Engineering, University College Dublin, Belfield, Dublin 4, Ireland. Die Arbeit wurde bisher 18-mal zitiert (Crossref) und nennt 53 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Science Foundation Ireland.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study investigated the print homogeneity of Ti-6Al-4 V alloy parts, when printed over a large build area of 250 $$\times$$ × 250 $$\times$$ × 170 mm 3 , using a production scale laser powder bed additive manufacturing system. The effect of part location across this large build area was investigated based on printed part porosity, microstructure, hardness, and tensile properties. In addition, a Hot Isostatic Pressing (HIP) treatment was carried out on the as-built parts, to evaluate its impact on the material properties. A small increase in part porosity from 0.01 to 0.09%, was observed with increasing distance from the argon gas flow inlet, which was located on one side of the build plate, during printing. This effect, which was found to be independent of height from the build plate, is likely to be associated with enhanced levels of condensate or spatter residue, being deposited at distances, further from the gas flow. Despite small differences in porosity, no significant differences were obtained for microstructural features such as prior β grain, $$\alpha$$ α lath thickness, and phase fraction, over the entire build area. Due to this, mechanical performances such as hardness and tensile strengths were also found to be homogenous across the build area. Additionally, it was also observed based on the lattice constants that partial in-situ decomposition of $${\alpha }^{^{\prime}}\to \alpha +\beta$$ α ′ → α + β phases occurred during printing. Post HIP treatment result showed a decrease of 7 and 6%, in the yield strength (YS) and ultimate tensile strength (UTS), respectively, which was associated with a coarsening of $$\alpha$$ α lath widths. The potential of the laser powder bed system for large area printing was successfully demonstrated based on the homogenous microstructure and mechanical properties of the Ti-6Al-4 V alloy parts.

Schlagwörter

Stichwörter der Autor:innen

HIPMicrostructure homogeneityPBF-LBPart placementTi-6Al-4 V

Autor:innen und Institutionen

  • School of Mechanical & Materials Engineering, University College Dublin, Belfield, Dublin 4, Ireland.
  • Department of Materials, The University of Manchester, Sackville Street Building, Manchester, M1 3BB UK.

Förderung

  • Science Foundation Ireland

Zitieren

APA

Bagasol, A. J. I., Kaschel, F. R., Ramachandran, S., Mirihanage, W., Browne, D. J., & Dowling, D. P. (2023). The influence of a large build area on the microstructure and mechanical properties of PBF-LB Ti-6Al-4 V alloy. The International Journal of Advanced Manufacturing Technology, 125(3-4), 1355-1369. https://doi.org/10.1007/s00170-022-10671-9

Vancouver

Bagasol AJI, Kaschel FR, Ramachandran S, Mirihanage W, Browne DJ, Dowling DP. The influence of a large build area on the microstructure and mechanical properties of PBF-LB Ti-6Al-4 V alloy. The International Journal of Advanced Manufacturing Technology. 2023;125(3-4):1355-1369. doi:10.1007/s00170-022-10671-9

BibTeX
@article{Bagasol2023,
  author = {Bagasol, Axieh Joy I and Kaschel, Frederico R and Ramachandran, Saranarayanan and Mirihanage, Wajira and Browne, David J and Dowling, Denis P},
  title = {The influence of a large build area on the microstructure and mechanical properties of PBF-LB Ti-6Al-4 V alloy},
  journal = {The International Journal of Advanced Manufacturing Technology},
  year = {2023},
  volume = {125},
  number = {3-4},
  pages = {1355--1369},
  doi = {10.1007/s00170-022-10671-9}
}
Kostenlos starten →