EUVIMEDEUVIMED entdecken
Crossref

Preparation of Ultra‐Thin Copper Foil for Enhancing the Lithium Metal Batteries Properties by Recycling Waste Printed Circuit Boards

Ming-Chen Gong, Ren-Fei Zhao, Xi-Xian Xia, Wei-Xi Yang, Zi-Liang Liu, Bo-Kuan Yan, Gen Chen, Shu-Hao Deng iD

Small Methods · 2026-04 · 10 (8)

DOI: 10.1002/smtd.202502198 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Small Methods, online erschienen am 24.03.2026. Verfasst von Ming-Chen Gong und 7 weiteren Autor:innen. Beteiligte Einrichtung: School of Materials Science and Engineering, Central South University, Changsha, P. R. China. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 48 Literaturangaben. Gefördert von: China Scholarship Council.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Among all metals in waste printed circuit boards (WPCBs), copper has the highest content and therefore carries significant recycling value. Meanwhile, as the anode current collector, ultra‐thin copper foil has great potential to enhance the performance of anode‐free lithium metal batteries (AFLMBs). However, the control of its complete stripping and mechanical properties still hinders this process. Herein, by utilizing a molybdenum substrate for the first time with a benzotriazole (BTA) stripping layer, the 3.5 µm ultra‐thin electrolytic copper foil (Ut‐Cu) with a tensile strength of 428 MPa is prepared and easily stripped through recycling WPCBs, presenting a highly preferred (111) orientation and nanotwin microstructure. When used as the anode current collector in LMBs, the Li||Cu half‐cells show more uniform lithium deposition and exhibit an average Coulombic efficiency (CE) of 97.7% over 300 cycles at 0.5 mA cm −2 . Furthermore, the Li@Cu||LFP cells retain 89.7% capacity after 200 cycles at room temperature, and the Cu||LFP (anode‐free) cells with Ut‐Cu show 68.8% capacity retention after 100 cycles, with the mass energy density increasing 39.4% compared with the commercial electrolytic copper foil (Com‐Cu). Moreover, the average copper recovery rate of WPCBs can reach as high as 67.7%, conducive to environmental protection and turning waste into treasure.

Schlagwörter

Stichwörter der Autor:innen

electrodepositionlithium metal batterynegative current collectorultra‐thin copper foilwaste circuit boards

Autor:innen und Institutionen

  • School of Materials Science and Engineering, Central South University, Changsha, P. R. China.
  • The State Key Laboratory of Powder Metallurgy, Changsha, P. R. China.

ORCID-Profile: Shu-Hao Deng

Förderung

  • China Scholarship Council

Zitieren

APA

Gong, M. C., Zhao, R. F., Xia, X. X., Yang, W. X., Liu, Z. L., Yan, B. K., Chen, G., & Deng, S. H. (2026). Preparation of Ultra‐Thin Copper Foil for Enhancing the Lithium Metal Batteries Properties by Recycling Waste Printed Circuit Boards. Small Methods, 10(8). https://doi.org/10.1002/smtd.202502198

Vancouver

Gong MC, Zhao RF, Xia XX, Yang WX, Liu ZL, Yan BK, et al. Preparation of Ultra‐Thin Copper Foil for Enhancing the Lithium Metal Batteries Properties by Recycling Waste Printed Circuit Boards. Small Methods. 2026;10(8). doi:10.1002/smtd.202502198

BibTeX
@article{Gong2026,
  author = {Gong, Ming-Chen and Zhao, Ren-Fei and Xia, Xi-Xian and Yang, Wei-Xi and Liu, Zi-Liang and Yan, Bo-Kuan and Chen, Gen and Deng, Shu-Hao},
  title = {Preparation of Ultra‐Thin Copper Foil for Enhancing the Lithium Metal Batteries Properties by Recycling Waste Printed Circuit Boards},
  journal = {Small Methods},
  year = {2026},
  volume = {10},
  number = {8},
  doi = {10.1002/smtd.202502198}
}
Kostenlos starten →