EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC 4.0

Fabrication of Eco‐Friendly Wearable Strain Sensor Arrays via Facile Contact Printing for Healthcare Applications

Shin-Da Wu iD, Shan-Hui Hsu iD, Bendix Ketelsen iD, Sophia C Bittinger iD, Hendrik Schlicke iD, Horst Weller iD, Tobias Vossmeyer iD

Small Methods · 2023-09 · 7 (9)

DOI: 10.1002/smtd.202300170 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Small Methods, online erschienen am 08.05.2023. Verfasst von Shin-Da Wu und 6 weiteren Autor:innen. Beteiligte Einrichtung: Institute of Polymer Science and Engineering, National Taiwan University, Taipei, 10617, Taiwan. Hauptthemen laut MEDLINE: Wearable Electronic Devices, Metal Nanoparticles. Die Arbeit wurde bisher 25-mal zitiert (Crossref) und nennt 127 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC 4.0). Gefördert von: Ministry of Science and Technology of Taiwan, Deutsche Forschungsgemeinschaft (DFG, German Research Foundation), Ministry of Science and Technology, Taiwan.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Wearable flexible strain sensors with spatial resolution enable the acquisition and analysis of complex actions for noninvasive personalized healthcare applications. To provide secure contact with skin and to avoid environmental pollution after usage, sensors with biocompatibility and biodegradability are highly desirable. Herein, wearable flexible strain sensors composed of crosslinked gold nanoparticle (GNP) thin films as the active conductive layer and transparent biodegradable polyurethane (PU) films as the flexible substrate are developed. The patterned GNP films (micrometer‐ to millimeter‐scale square and rectangle geometry, alphabetic characters, and wave and array patterns) are transferred onto the biodegradable PU film via a facile, clean, rapid and high‐precision contact printing method, without the need of a sacrificial polymer carrier or organic solvents. The GNP‐PU strain sensor with low Young's modulus (≈17.8 MPa) and high stretchability showed good stability and durability (10 000 cycles) as well as degradability (42% weight loss after 17 days at 74 °C in water). The GNP‐PU strain sensor arrays with spatiotemporal strain resolution are applied as wearable eco‐friendly electronics for monitoring subtle physiological signals (e.g., mapping of arterial lines and sensing pulse waveforms) and large‐strain actions (e.g., finger bending).

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Wearable Electronic DevicesMetal NanoparticlesGoldSkinDelivery of Health Care

Stichwörter der Autor:innen

biodegradable polyurethaneeco-friendly electronicsgold nanoparticlesensor arrayswearable flexible strain sensors

Substanzen

Gold

Autor:innen und Institutionen

  • Institute of Polymer Science and Engineering, National Taiwan University, Taipei, 10617, Taiwan.
  • Institute of Physical Chemistry, University of Hamburg, 20146, Hamburg, Germany.
  • Institute of Cellular and System Medicine, National Health Research Institutes, Miaoli, 35053, Taiwan.
  • Fraunhofer Center for Applied Nanotechnology CAN, 20146, Hamburg, Germany.

ORCID-Profile: Shin-Da Wu, Shan-Hui Hsu, Bendix Ketelsen, Sophia C Bittinger, Hendrik Schlicke, Horst Weller, Tobias Vossmeyer

Förderung

  • Ministry of Science and Technology of Taiwan
  • Deutsche Forschungsgemeinschaft (DFG, German Research Foundation)
  • Ministry of Science and Technology, Taiwan

Zitieren

APA

Wu, S. D., Hsu, S. H., Ketelsen, B., Bittinger, S. C., Schlicke, H., Weller, H., & Vossmeyer, T. (2023). Fabrication of Eco‐Friendly Wearable Strain Sensor Arrays via Facile Contact Printing for Healthcare Applications. Small Methods, 7(9). https://doi.org/10.1002/smtd.202300170

Vancouver

Wu SD, Hsu SH, Ketelsen B, Bittinger SC, Schlicke H, Weller H, et al. Fabrication of Eco‐Friendly Wearable Strain Sensor Arrays via Facile Contact Printing for Healthcare Applications. Small Methods. 2023;7(9). doi:10.1002/smtd.202300170

BibTeX
@article{Wu2023,
  author = {Wu, Shin-Da and Hsu, Shan-Hui and Ketelsen, Bendix and Bittinger, Sophia C and Schlicke, Hendrik and Weller, Horst and Vossmeyer, Tobias},
  title = {Fabrication of Eco‐Friendly Wearable Strain Sensor Arrays via Facile Contact Printing for Healthcare Applications},
  journal = {Small Methods},
  year = {2023},
  volume = {7},
  number = {9},
  doi = {10.1002/smtd.202300170}
}
Kostenlos starten →