EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Controlling Droplet Evaporation in Aerosol Jet Printing to Understand and Mitigate Overspray

Bella I Guyll, Brayden L Sanford, Cary L Pint iD, Ethan B Secor iD

Small Science · 2025-07 · 5 (7)

DOI: 10.1002/smsc.202500069 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Small Science, online erschienen am 18.03.2025. Verfasst von Bella I Guyll und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering Iowa State University Ames Iowa 50011 USA. Die Arbeit wurde bisher 25-mal zitiert (Crossref) und nennt 36 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: DARPA.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Aerosol jet printing is an additive manufacturing technique with broad materials compatibility, high resolution, and complex geometric capabilities. Despite these advantages, even optimized prints are susceptible to overspray, in which sparse deposition of material outside the primary pattern limits precision and quality for high‐value applications. Herein, a method is presented to overcome this by loading the sheath gas with solvent vapor before entering the printhead. This reduces droplet drying in the aerosol phase at the periphery of the aerosol stream, improving line edge morphology, pitch, porosity, and surface finish. This is demonstrated to reduce the overspray extent for a water‐based polyimide ink by up to 70 ± 2.3% and decrease the resistivity of a solvent‐based silver ink by 34 ± 13%. The ability to regulate droplet evaporation in flight offers versatile control, facilitating a wider range of process parameters and ink chemistries. These experimental results are backed by theoretical analysis and numerical modeling, providing a more refined and generalizable understanding of the underlying process physics. This enables tailored outcomes for a range of challenges including high aspect ratio and high‐density patterning with improved surface finish and material functionality for compelling applications in printed and hybrid electronics.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturingmicrofabricationmultiphase flownanomaterial inksprinted electronics

Autor:innen und Institutionen

  • Department of Mechanical Engineering Iowa State University Ames Iowa 50011 USA.

ORCID-Profile: Cary L Pint, Ethan B Secor

Förderung

  • DARPA

Zitieren

APA

Guyll, B. I., Sanford, B. L., Pint, C. L., & Secor, E. B. (2025). Controlling Droplet Evaporation in Aerosol Jet Printing to Understand and Mitigate Overspray. Small Science, 5(7). https://doi.org/10.1002/smsc.202500069

Vancouver

Guyll BI, Sanford BL, Pint CL, Secor EB. Controlling Droplet Evaporation in Aerosol Jet Printing to Understand and Mitigate Overspray. Small Science. 2025;5(7). doi:10.1002/smsc.202500069

BibTeX
@article{Guyll2025,
  author = {Guyll, Bella I and Sanford, Brayden L and Pint, Cary L and Secor, Ethan B},
  title = {Controlling Droplet Evaporation in Aerosol Jet Printing to Understand and Mitigate Overspray},
  journal = {Small Science},
  year = {2025},
  volume = {5},
  number = {7},
  doi = {10.1002/smsc.202500069}
}
Kostenlos starten →